การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Fuller, Pritchel and Hot Setts: Steel Welded into a Split Iron Bar, with Twisted Rod or Withy Handles (Edwinson, 1886)
Forge

สร้างโดย

Forge

14. พฤศจิกายน 2026NO
6
0
0
0
0

Fuller, Pritchel and Hot Setts: Steel Welded into a Split Iron Bar, with Twisted Rod or Withy Handles (Edwinson, 1886)

The smith's own top and bottom tools, from George Edwinson's farrier's chapter in Amateur Work (1886): an inch iron bar upset, split into a fork and a steel wedge welded in, then forged into a fuller, pritchel punch, curved or straight hot sett, or a square-tanged bottom sett; the pritchel itself from 1/2 in. square tool steel; handles of twisted iron rod or green withy.
ขั้นสูง
A day at the forge for the set

คำแนะนำ

1

His proportions

กำลังโหลดสมุด Jupyter…
2

Read Edwinson

"To make this tool, heat and upset the end of an inch bar of iron; then heat again and split with a sett."
3

Split the iron

Heat and upset the end of a 1 in. (25 mm) iron bar. Heat again and split it with a hot set into a fork 1 to 1 1/4 in. long by 3/4 in. wide (his fig. 108).

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กดัดแท่งเหล็กดัด1 ชิ้น

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนปอนด์ค้อนปอนด์
สกัดร้อนสกัดร้อน
คีมช่างตีเหล็กคีมช่างตีเหล็ก
4

Weld in the steel

Heat the end of a steel bar of similar size and forge a wedge to fit the fork (fig. 109). Bring both to a welding heat and weld them well together.

วัสดุสำหรับขั้นตอนนี้:

เหล็กกล้าเบ้าหลอมเหล็กกล้าเบ้าหลอม1 ชิ้น
ผงบอแรกซ์ผงบอแรกซ์1 ชิ้น

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนปอนด์ค้อนปอนด์
คีมช่างตีเหล็กคีมช่างตีเหล็ก
5

Forge the fuller

Cut off 2 in. of steel and 3 in. of iron for the tool. Forge the steel, with the iron behind it, into the fuller's rounded blade (fig. 102). Make the neck while it is still on the bar, then cut it off leaving a piece of iron for the head.

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนค้อน
สกัดร้อนสกัดร้อน
6

Same blank, other tools

Pritchel punch: about 2 in. of iron and 1 in. of steel, shaped as fig. 103. Curved set: as the fuller but with a gouge-shaped blade (fig. 105). Top hot set: the same, with a chisel or wedge blade (fig. 106). Bottom set: a wedge of steel and iron, edge up, on a square tang that fits the anvil's square hole (fig. 107).

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กดัดแท่งเหล็กดัด1 ชิ้น
เหล็กกล้าเบ้าหลอมเหล็กกล้าเบ้าหลอม1 ชิ้น
ผงบอแรกซ์ผงบอแรกซ์1 ชิ้น

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนค้อน
ค้อนปอนด์ค้อนปอนด์
คีมช่างตีเหล็กคีมช่างตีเหล็ก
7

Forge the pritchel

Forge 1/2 in. (13 mm) square tool steel into the tapered pritchel (fig. 104), 6 in. (150 mm) long. It punches nail holes in hot iron, so it need not be hardened.

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กกล้าเครื่องมือแท่งเหล็กกล้าเครื่องมือ1 ชิ้น

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนค้อน
คีมช่างตีเหล็กคีมช่างตีเหล็ก
8

Fit the handles

Rod handle: twist 3/8 in. iron rod once round the neck and weld the two ends together (fig. 110). Withy handle: take a green or half-green hazel, willow, oak or withy rod about 3 ft long, twist the middle 8-9 in., wrap it once round the neck and bind the two ends with wire or a link (figs. 106, 111).

วัสดุสำหรับขั้นตอนนี้:

เหล็กเส้นกลมเหล็กกล้าละมุนเหล็กเส้นกลมเหล็กกล้าละมุน1 ชิ้น
กิ่งหลิว (อ่อนตัว)กิ่งหลิว (อ่อนตัว)1 ชิ้น
ลวดเหล็กดัดลวดเหล็กดัด1 ชิ้น

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนค้อน
คีมช่างตีเหล็กคีมช่างตีเหล็ก
9

Harden the cutting tools (ours)

He gives no temper for these. Ours: harden and temper the set edges as for other hot-cutting tools, and cool them often in use.

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ถังชุบน้ำถังชุบน้ำ
10

Troubleshooting

Top-tool troubleshooting.

Flow

Loading...
11

History and honest limits

From George Edwinson, "Smithing and Forging" VII, **Amateur Work, Illustrated**, vol. VI (1886-87), pp. 14-16 and figs. 101-111 (checked on the archive.org scan amateurworkillus06lond). He calls the top hot cutter a "sett"; we map it to the Hot Chisel head and the bottom sett to the Hot Cut Hardy head. Temper, metric figures and tools are ours.

วัสดุ

7

เครื่องมือที่จำเป็น

7

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...