ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Sliding-Strip Cylinder Dash Churn: Strips on the Slats Open the Gaps One Way and Close Them the Other
Daniel K. France of Congress, Ohio, received US 25,404, dated 13 September 1859, for a cylindrical churn-dash. Two crosses of curved arms carry four groups of three slats, each slat half by one inch. On each group a metal strip with a slot down its middle is held by screws in short slots, so it slides when the dash changes direction and opens or closes the spaces between the slats. Turned one way the dash churns; reversed, it gathers the butter into a corner. Two cog wheels at three to one drive it.
France gives one size, the slats; every other size here is ours.
ระดับกลาง
About 2 days, plus printing
คำแนะนำ
1
1
France's slats, and the wheels' three to one
France's slats, and the wheels' three to one
กำลังโหลดสมุด Jupyter…
2
2
A turning dasher on crossed arms in a box, before it
A turning dasher on crossed arms in a box, before it
That dasher's boards were fixed. France's slats carry strips that open and close the gaps with the turning.
3
3
Read US 25,404
Read US 25,404
"The motion of the dash to be to the left in the direction of the curve of the arms while churning, thereby producing the greatest amount of friction in the cream. When butter is produced the motion of the dash is reversed and the butter gathered in the lower left corner of the churn by the reversed action thereon of the dash and self adjusting slide."
4
4
Print the large cog wheel
Print the large cog wheel
The 48-tooth spur wheel (module 3) with a hub, bored 20.4 mm, for the crank's stud. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the small cog wheel
Print the small cog wheel
The 16-tooth spur pinion (module 3) with a hub, bored 20.4 mm, for the dash's shaft. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Box with legs and lid
Box with legs and lid
From 20 mm hardwood cut a bottom 440 x 340 mm, two sides 440 x 300 mm, two ends 300 x 300 mm and a lid 440 x 340 mm. Bore each end 20.8 mm through its middle, 150 mm above the floor, for the shaft. Glue and screw the ends between the sides and the box onto the bottom, and screw four legs of 70 mm timber, 350 mm long, under it. Fill the box with water overnight so it swells tight, then empty it.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง3 ชิ้น
ไม้เนื้ออ่อน 70x70 มม.1 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้30 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
เลื่อยมือ
สว่านไร้สาย
ชุดดอกสว่านใบพาย
แคลมป์แบบบาร์
ฉากตาย
ตลับเมตร
น้ำ7
7
Dash: arms, hubs and slats
Dash: arms, hubs and slats
Cut eight curved arms from 22 mm hardwood with the jigsaw, each 18 mm wide, sweeping 30 degrees from a 20 mm hub radius out to 112 mm. Glue four into a 56 mm hardwood hub to make a cross, twice, all curving the same way, and bore the hubs 20.4 mm. Cut twelve slats 12.7 x 25.4 mm, 340 mm long, and screw them to the arms' ends in groups of three, 9 mm apart, flat side out, so their faces are 125 mm from the middle.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้24 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยจิ๊กซอว์
เลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สาย
ชุดดอกสว่านใบพาย
ชุดดอกสว่าน
ตลับเมตร8
8
Strips B with slots C and screws D
Strips B with slots C and screws D
Cut four strips of 0.8 mm stainless sheet, 324 mm long and as wide as a group of slats (94 mm). Cut a slot C 9 mm wide along the middle of each, stopping 30 mm from the ends, and a short slot across each end. Lay each strip on its group's outer face and fix it with an M4 screw through each end slot into the arm's end, just loose enough to slide sideways. Turned one way, the cream pushes each strip so its slot lies over the slats; the other way, over a space.
วัสดุสำหรับขั้นตอนนี้:
แผ่นสเตนเลส1 ชิ้น
สกรูเกลียวมิล8 ชิ้น
แหวนรองแบน8 ชิ้นเครื่องมือที่ต้องใช้:
กรรไกรตัดแผ่นโลหะ
ตะไบ (ตะไบมือ)
สว่านไร้สาย
ชุดดอกสว่าน
ชุดไขควง9
9
Shaft, cog wheels and crank
Shaft, cog wheels and crank
Pass a 20 mm stainless shaft through one end of the box, the two hubs and the other end, and pin the hubs to it. On the outside of the geared end, screw a hardwood block 96 mm above the shaft, fix a 20 mm stud in it, and fit the large wheel on the stud with a crank and handle. Pin the small wheel on the shaft's end meshing with it.
วัสดุสำหรับขั้นตอนนี้:
แท่งสเตนเลส2 ชิ้น
แผ่นไม้เนื้อแข็ง1 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาด3 ชิ้น
นอตล็อกไนลอน3 ชิ้น
เส้นใย PETG1 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยตัดเหล็ก
สว่านไร้สาย
ชุดดอกสว่าน
ประแจเลื่อน10
10
The build in 3D
The build in 3D
FreeCAD model of this build, front side cut away: the dash's two crosses of curved arms, the four groups of slats with their strips, slots and screws, the shaft through the box's ends, and the two cog wheels and crank outside. The dash was turned through 16 angles.
11
11
Churn, then gather
Churn, then gather
Pour about 6 litres of heavy cream at about 15 °C into the box, checked with the thermometer, and put the lid on. Turn the crank so the dash turns with the curve of its arms, timing it. When the butter comes, turn the crank the other way so the strips slide over and the dash gathers the butter into a corner. Lift it out, drain the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด6 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่12
12
Troubleshooting
Troubleshooting
Sliding-strip churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Daniel K. France** of Congress, Wayne County, Ohio, US 25,404, 13 September 1859, "Churn-Dash". He claimed the metallic strips B on the convex surface of the slats, held by slots and screws. He disclaimed slats or beaters hinged to the arms. His slats, half by one inch, are kept; every other size is ours. His plates A, changed to reverse the dash when the crank is used alone, are not built.
วัสดุ
15- 3 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 54 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 8 ชิ้นตัวยึดตำแหน่ง
- 8 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 6 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
20- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
3พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

Rotary-Dasher Box Churn: Float Boards on Crossed Arms in a Curved Box
โดย Martin
อาหารและเครื่องดื่ม
51
0
0
0
0
0

Hinged-Float Double-Dasher Churn: Floats That Close Going Down and Fall Open Coming Up
โดย Buttercup
งานไม้
10
0
0
0
0
0

Water-Chamber Box Churn: A Turning Box With a Dash-Frame You Lower to Free the Butter
โดย Buttercup
งานไม้
14
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
โดย TheChef
งานฝีมือ
63
0
0
0
0
0
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

