การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Gasholder: Water-Sealed Zinc Gasometer with Balance Weights (Ramsay & Travers, 1898)
Charlie

สร้างโดย

Charlie

4. พฤศจิกายน 2026DE
9
0
0
0
0

Gasholder: Water-Sealed Zinc Gasometer with Balance Weights (Ramsay & Travers, 1898)

The laboratory gasometer Ramsay and Travers used to store argon: a zinc bell that rises and falls in a narrow ring of water between two fixed zinc cylinders. Because the water space is only about 2 cm wide, little gas dissolves in it. Weights on cords over pulleys balance the bell, and weights laid on top push the gas out. Result: a water-sealed gasholder of 18 to 180 litres. Source: M. W. Travers, The Experimental Study of Gases (1901), pp. 30 and 105-106. Unknown: sizes and how the zinc is joined. Picture: Fig. 34, the small mercury form of the same design.
ระดับกลาง
Unknown

คำแนะนำ

1

Make the fixed cylinders

Make two concentric zinc cylinders on a closed base, leaving a ring-shaped space about 2 cm wide between them for the water. Make the top of the inner cylinder dome-shaped. Bring a gas pipe with a stopcock up through the inner cylinder. Ours: zinc soldered with tin-lead solder. Not given: sizes, how the zinc is joined, the stopcock.

วัสดุสำหรับขั้นตอนนี้:

แผ่นสังกะสีแผ่นสังกะสี1 outer and inner cylinders, base
ตะกั่วบัดกรีดีบุก-ตะกั่วตะกั่วบัดกรีดีบุก-ตะกั่ว1 seams
วาล์วที่ไม่ทราบวาล์วที่ไม่ทราบ1 gas stopcock

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
หัวแร้งบัดกรีหัวแร้งบัดกรี
วิธีขึ้นรูปที่ไม่ทราบวิธีขึ้นรูปที่ไม่ทราบ
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
2

Make and hang the bell

Make the gasholder bell of zinc to fit closely over the inner cylinder and down into the water ring, with a dome-shaped top matching the inner cylinder's, so all the gas can be pushed out. Ramsay and Travers made bells of about 180, 27, 18 and 18 litres. Tie a cord to the top of the bell and pass it over pulleys to a hanging weight, to take the bell's own weight off the gas. Fill the ring with water. To deliver gas, take weight off the cord or lay weights on top of the bell. Not given: the weights.

วัสดุสำหรับขั้นตอนนี้:

แผ่นสังกะสีแผ่นสังกะสี1 bell
ตะกั่วบัดกรีดีบุก-ตะกั่วตะกั่วบัดกรีดีบุก-ตะกั่ว1 seams
เชือกป่านเชือกป่าน1 balance cords
รอกรอก2 pulleys
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 balance weights

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
หัวแร้งบัดกรีหัวแร้งบัดกรี

วัสดุ

6

เครื่องมือที่จำเป็น

4

พิมพ์เขียวนี้สร้าง

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...