การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Half-Round Taper Reamer: Tool Steel Turned to the Taper, Filed Flat to the Centre Line, Hardened (Griswold, Amateur Work, 1905)
Forge

สร้างโดย

Forge

14. พฤศจิกายน 2026NO
9
0
0
0
0

Half-Round Taper Reamer: Tool Steel Turned to the Taper, Filed Flat to the Centre Line, Hardened (Griswold, Amateur Work, 1905)

The simplest home-made taper reamer, from Robert Gibson Griswold's Tool Making for Amateurs (Boston, 1905): tool steel turned to the taper wanted (his was 1/8 in. per foot), one side filed away exactly to the centre line so that two cutting edges remain, then hardened and ground on the flat face only. It reams a very smooth conical hole.
ระดับกลาง
Two to three hours

คำแนะนำ

1

His taper

กำลังโหลดสมุด Jupyter…
2

Read Griswold

"Turn a piece of tool steel to the proper taper and then file away one side until the flat surface coincides with the center line."
3

Turn the taper

Turn a piece of tool steel in the lathe to the taper of the part the hole must fit (his: 1/8 in. per foot). Length and diameter are ours: a little longer than the hole and spanning its two diameters.

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กกล้าเครื่องมือแท่งเหล็กกล้าเครื่องมือ1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
เวอร์เนียคาลิปเปอร์เวอร์เนียคาลิปเปอร์
4

File to the centre line

Hold it in the vice and file away one side until the flat face lies exactly on the centre line. This leaves a cutting edge on each side.

เครื่องมือที่ต้องใช้:

ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
เวอร์เนียคาลิปเปอร์เวอร์เนียคาลิปเปอร์
5

Harden and grind

Harden it (ours: heat to a cherry red and quench in water, temper to a straw colour), then grind on the flat side only, never on the round.

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ถังชุบน้ำถังชุบน้ำ
เครื่องเจียรตั้งโต๊ะเครื่องเจียรตั้งโต๊ะ
6

Troubleshooting

Reamer troubleshooting.

Flow

Loading...
7

History and honest limits

From Robert Gibson Griswold, "Tool Making for Amateurs" VII, **Amateur Work** (Boston), vol. IV (1904-05), p. 128 (checked on the archive.org scan amateurwork04bostrich). He gives no size or temper for the reamer; those and the tools are ours. He finishes the hardened bushings with a copper lap and emery.

วัสดุ

1

เครื่องมือที่จำเป็น

7

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...