ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
One-Screw Two-Part Shaft Collar: Hooked Ends Reach Round the Shaft So the Halves Cannot Open (Grundy, 1907)
Forge

สร้างโดย

Forge

13. พฤศจิกายน 2026NO
5
0
0
0
0

One-Screw Two-Part Shaft Collar: Hooked Ends Reach Round the Shaft So the Halves Cannot Open (Grundy, 1907)

John R. Grundy of Philadelphia received US 860,369, dated 16 July 1907, for a two-part collar held by a single screw, where earlier split collars needed two. The screw passes through one pair of ends, an overhang on one part lying over the other. At the opposite side a tongue on one part fits a recess in the other. Both of those ends reach round the shaft past the diameter under the screw. When the screw's point presses the shaft, they hook under it and cannot open. Each part goes onto the shaft from the side, so the shaft stays in its bearings. We cut the two parts from a turned brass ring with a piercing saw, from a full-size template. The patent gives no sizes; every size here is ours.
ขั้นสูง
About 2 days

คำแนะนำ

1

Why the hooks hold

กำลังโหลดสมุด Jupyter…
2

Read US 860,369

"It is obvious that by using the single screw in place of a plurality of screws, as has hitherto been considered necessary, I am enabled to reduce the cost of the collar." "The parts of said collar are placed in position on the shaft by being moved toward it in radial planes."
3

Turn the ring

Grip 45 mm brass round bar in the 3-jaw chuck. Face it, turn it to 40 mm for 20 mm, centre-drill, drill through 15 mm and ream 16 mm. Part off 16 mm long and face the parted side.

วัสดุสำหรับขั้นตอนนี้:

แท่งทองเหลืองกลมแท่งทองเหลืองกลม1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
หัวจับกลึงสามจับหัวจับกลึงสามจับ
มีดกลึงมีดกลึง
ชุดดอกสว่านนำศูนย์ชุดดอกสว่านนำศูนย์
ชุดดอกสว่านชุดดอกสว่าน
ดอกรีมเมอร์ดอกรีมเมอร์
มีดตัดงานกลึงมีดตัดงานกลึง
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
แว่นนิรภัยแว่นนิรภัย
4

Print the cutting template

Full-size A4 template: the end view of the ring with the outlines of parts B and B', and the bottom of the ring seen from below with the tongue b' and cheeks a'. Print at 100 %; its 50 mm bar must measure 50 mm.
ไฟล์แบบPDFCC0 - Free
5

Cut the parts apart

Glue the end view on one end face of the ring, centred, and the strip on the outside at the bottom. Wax the blade. Top joint: hold the ring in soft jaws, face up, and saw with the blade along the axis: in from the outside 5 mm left of the line to 14 mm radius, round the 14 mm circle to the line, and down the line into the bore. Bottom joint: turn the ring over and saw with the blade across the wall, following the strip from one end face to the other: the cheeks a' 3 mm left of the line, the tongue b' 3 mm right of it. Go slowly at the corners; the two parts come apart.

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์อิงก์เจ็ตเครื่องพิมพ์อิงก์เจ็ต
กาวกาว
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ปากอ่อนสำหรับปากกาจับชิ้นงานปากอ่อนสำหรับปากกาจับชิ้นงาน
เลื่อยช่างทองเลื่อยช่างทอง
ขี้ผึ้งขี้ผึ้ง
6

Fit the joints and cut away the bores

File the saw marks off the joints until the tongue slides into its recess and the overhang lies on the other part, with the two parts round a 16 mm bar. File each part's bore out to 18 mm across over the 22 degrees next to the top joint on its own side, B' to the left of the line and B to the right, as the template shows. Try them on the bar: put B on from below right, then B' from below left, sliding it up under the overhang and the tongue into its recess. File until each goes on without forcing.

เครื่องมือที่ต้องใช้:

เหล็กเส้นกลมเหล็กกล้าละมุนเหล็กเส้นกลมเหล็กกล้าละมุน
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ปากอ่อนสำหรับปากกาจับชิ้นงานปากอ่อนสำหรับปากกาจับชิ้นงาน
ชุดตะไบชุดตะไบ
ชุดตะไบเข็มชุดตะไบเข็ม
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
7

Drill and tap for the screw

With both parts on the bar, the overhang lying on B', clamp the bar in the machine vice so the dashed screw line on the template stands upright. Drill 4.2 mm through the overhang and through B' into the bore, and tap M5 through both with cutting oil. Take the parts off and deburr the bore.

วัสดุสำหรับขั้นตอนนี้:

น้ำมันตัดกลึงน้ำมันตัดกลึง1 ชิ้น

เครื่องมือที่ต้องใช้:

เหล็กเส้นกลมเหล็กกล้าละมุนเหล็กเส้นกลมเหล็กกล้าละมุน
สว่านแท่นสว่านแท่น
ปากกาจับชิ้นงานของเครื่องปากกาจับชิ้นงานของเครื่อง
ชุดดอกสว่านชุดดอกสว่าน
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
ด้ามจับต๊าปเกลียวด้ามจับต๊าปเกลียว
เครื่องมือลบครีบเครื่องมือลบครีบ
8

The collar in 3D

FreeCAD model, our sizes: parts B and B' on a 16 mm shaft, the overhang b and the M5 screw at the top, the tongue b' between the cheeks a' at the bottom, and the bores cut away beside the top joint.
ไฟล์แบบSTLCC0 - Free
9

Fit it on the shaft

Run an M5 x 12 cup point set screw into the overhang until it just shows. Put B onto the shaft from the side where the collar is wanted, then B' from the other side, its top under the overhang and its tongue into the recess. Tighten the screw with the hex key: it pushes on the shaft and draws both bottom ends down against it. Try to slide and turn the collar; it must not move.

วัสดุสำหรับขั้นตอนนี้:

สกรูหนอนปลายเว้าสกรูหนอนปลายเว้า1 ชิ้น

เครื่องมือที่ต้องใช้:

ชุดประแจหกเหลี่ยมชุดประแจหกเหลี่ยม
10

Troubleshooting

Grundy collar troubleshooting.

Flow

Loading...
11

History and honest limits

**John R. Grundy** of Philadelphia, US 860,369, dated 16 July 1907, filed 28 January 1907. He claimed "a shaft collar made in two parts, and means for holding the parts together comprising a single screw passing through two adjacent ends of said two parts, the other ends of said parts being formed to co-act with the shaft to prevent their separation". His screw end also has a second projection b2 in a recess, holding the parts in line along the shaft; ours leaves it out, as the screw through both parts does that. His screw has a hex head; ours is a socket set screw. He gives no material; ours is brass, which a piercing saw cuts well. The patent gives no sizes; every size here is ours.

วัสดุ

3

เครื่องมือที่จำเป็น

24

ไฟล์ออกแบบ

2

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...