การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Hackle Combs: Coarse and Fine Flax Heckles on One Board (Ure, 1839)
A pair of flax heckles on one oblong plank: two round wooden blocks, each faced with a drilled brass or iron plate holding upright iron teeth. Flax is drawn first through the coarse heckle, then through the fine one, splitting the fibres, combing out the short tow and laying the long fibres straight.
Coarse: teeth about 1/10 in thick and 1 1/4 in long, a centre tooth and 12 rings, the outer ring 5 3/4 in across. Fine: thinner teeth set closer, 1109 of them.
Source: Andrew Ure, Dictionary of Arts, Manufactures and Mines (1839), 'Flax'. Picture: Figs. 424-425 of the book.
ระดับกลาง
Unknown
คำแนะนำ
1
1
Make the board and blocks
Make the board and blocks
Cut an oblong plank (Fig. 424, a b) and two round (or square) wooden blocks, c for the coarse heckle and d for the fine, and fix the blocks on the plank (Fig. 425). The heckles can also be made on separate boards.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็งหนา1 ชิ้น
ท่อนไม้เนื้อแข็ง2 ชิ้น
สกรูไม้1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยสันแข็ง
ไขควงปากแบน2
2
Drill the face plates
Drill the face plates
Cover the top of each block with a brass or iron plate drilled for the teeth, which gives them a firmer hold. Set the holes evenly over the whole face, in concentric circles (the German way) or parallel rows (the English way). Coarse: a centre hole and 12 rings, the outermost 5 3/4 in across. Fine: thinner holes set closer, 1109 in all.
วัสดุสำหรับขั้นตอนนี้:
แผ่นทองเหลือง2 face platesเครื่องมือที่ต้องใช้:
วงเวียนปลายแหลมสองขา
กรรไกรตัดแผ่นโลหะ
สว่านมือ3
3
Make the teeth
Make the teeth
Cut teeth of iron (sometimes steel) 1 to 2 in long. For the coarse heckle make them about 1/10 in thick and 1 1/4 in long, tapering from the middle to a very fine point; the fine heckle's teeth are thinner. File every point sharp and smooth, running evenly into the round stem like a sewing needle; square points in a rhombus shape cut the fibres apart better than round ones.
วัสดุสำหรับขั้นตอนนี้:
ลวดเหล็กดัด1 teethเครื่องมือที่ต้องใช้:
กรรไกรตัดแผ่นโลหะ
ตะไบโลหะ4
4
Set the teeth
Set the teeth
Drive each tooth through its hole in the plate into the block so it stands upright, all points at one level.
เครื่องมือที่ต้องใช้:
ค้อนวัสดุ
5- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 face platesตัวยึดตำแหน่ง
- 1 teethตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

