การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Lady's Side Saddle: Stuffed Head, Small Off-Head, Bolstered Safe and Leather Girth (Hasluck, Saddlery, 1904)
Tex

สร้างโดย

Tex

13. พฤศจิกายน 2026FO
9
0
0
0
0

Lady's Side Saddle: Stuffed Head, Small Off-Head, Bolstered Safe and Leather Girth (Hasluck, Saddlery, 1904)

On a side saddle the rider sits with both legs on the near side, the right knee over a stuffed head in front. This is the side saddle from Paul N. Hasluck's Saddlery (1904): a bought tree with a small off-head, the seat built like the gentleman's saddle but padded higher on the riding side, a quilted (bolstered) safe on the near side, and a thin leather girth that buckles from the saddle. He refers back to the gentleman's saddle for many steps, and so does this blueprint.
ขั้นสูง
About 4-5 days

คำแนะนำ

1

His sizes in centimetres

กำลังโหลดสมุด Jupyter…
2

Read Saddlery, ch. III

"The head or point is the part projecting on the side of the saddle in front, over which the rider's knee is placed"; "the safe is the part in front which reaches beyond the saddle, covering the horse's shoulder to keep the rider's clothes from the horse." The tree (Fig. 6) is bought; trees differ in head, seat and cantle.
3

Web the tree and build the seat ground

Get a side saddle tree with a small off-head. Strain the web thoroughly and fit the cross pieces and linen to form a ground for the seat, exactly as for the gentleman's saddle. Cover it with white serge for stuffing, but make the sausage pad on the side where the rider sits nearly twice as thick as on the off side: if the seat ran down steep towards the riding side, the rider could fall. Increase the rounding gradually, sloping it down towards the front; sharp corners there would hurt the rider.

วัสดุสำหรับขั้นตอนนี้:

โครงอานข้างโครงอานข้าง1 ชิ้น
สายผ้าขึงตึงสายผ้าขึงตึง1 ชิ้น
ผ้าลินินผ้าลินิน1 ชิ้น
ผ้าเสิร์จขนสัตว์ผ้าเสิร์จขนสัตว์1 ชิ้น
ใยขนแกะสำหรับยัดใยขนแกะสำหรับยัด1 ชิ้น
ตะปูตะปู1 ชิ้น
ด้ายลินินด้ายลินิน1 ชิ้น
ขี้ผึ้งขี้ผึ้ง1 ชิ้น

เครื่องมือที่ต้องใช้:

คีมปากนกแก้วคีมปากนกแก้ว
ค้อนหงอนค้อนหงอน
กรรไกรกรรไกร
เข็มเย็บอานม้าสองเล่มเข็มเย็บอานม้าสองเล่ม
เหล็กหมาด (สว่านเจาะรูมือ)เหล็กหมาด (สว่านเจาะรูมือ)
4

Stuff the head

Before covering the seat: cut two pieces of stiff leather the shape of the head, reaching to the bottom on the inside and large enough outside to stitch round the horn. Stitch one firmly on each side, put two or three tacks in the outer one at the bottom, and thin and shape the edges. Shape white serge to the head, round at the top and about 2-1/2 in wider along the sides and as much longer at the top; tack round it with white linen thread, turning the edges in and puckering the top so it bulges when stuffed. Stitch it inside the head to the stitches in the leathers so it covers the edge of the horn, bulging equally all round. Stuff clean carded flock, cut small, from the bottom, pushing it up with the seat awl until firm, plump and smooth; hold it with a few loose stitches back and forth along the sides, top up the centre if needed and level it with the seat awl.

วัสดุสำหรับขั้นตอนนี้:

หนังทำเครื่องม้าหนังทำเครื่องม้า1 ชิ้น
ผ้าเสิร์จขนสัตว์ผ้าเสิร์จขนสัตว์1 ชิ้น
ใยขนแกะสำหรับยัดใยขนแกะสำหรับยัด1 ชิ้น
ด้ายลินินด้ายลินิน1 ชิ้น
ขี้ผึ้งขี้ผึ้ง1 ชิ้น
ตะปูตะปู1 ชิ้น

เครื่องมือที่ต้องใช้:

มีดตัดหนังมีดตัดหนัง
กรรไกรกรรไกร
เหล็กหมาด (สว่านเจาะรูมือ)เหล็กหมาด (สว่านเจาะรูมือ)
เข็มเย็บอานม้าสองเล่มเข็มเย็บอานม้าสองเล่ม
เหล็กเกลี่ยที่นั่งเหล็กเกลี่ยที่นั่ง
ค้อนหงอนค้อนหงอน
5

Cover and stuff the seat

Put serge on the outer side of the small head, nailed at the bottom and turned in along its edge. Put on the serge seat cover as for the gentleman's saddle, but cut it round the stuffed horn, turn the edges under and nail the ends in front; along the small horn, turn in the seat cover's edge and whip it to the turned-in edge of the piece underneath. Cut the slit in the centre and stuff as for the gentleman's saddle. Quilt along the ridge from the near-side horn to the root of the cantle, giving a flat, full, square edge, and the same on the other side; refill and level the centre and both points with the seat awl.

วัสดุสำหรับขั้นตอนนี้:

ผ้าเสิร์จขนสัตว์ผ้าเสิร์จขนสัตว์1 ชิ้น
ใยขนแกะสำหรับยัดใยขนแกะสำหรับยัด1 ชิ้น
ตะปูตะปู1 ชิ้น
ด้ายลินินด้ายลินิน1 ชิ้น
ขี้ผึ้งขี้ผึ้ง1 ชิ้น

เครื่องมือที่ต้องใช้:

กรรไกรกรรไกร
ค้อนหงอนค้อนหงอน
เหล็กหมาด (สว่านเจาะรูมือ)เหล็กหมาด (สว่านเจาะรูมือ)
เข็มเย็บอานม้าสองเล่มเข็มเย็บอานม้าสองเล่ม
เหล็กเกลี่ยที่นั่งเหล็กเกลี่ยที่นั่ง
6

Cover the head and seat in hogskin

Nail hogskin over the long point at the back, pull it tight and tack it close round the top to remove every pleat; leave it to dry. Damp the hogskin seat and put it on, with a small piece of hogskin outside the small point; cut the seat round the long point, cross the ends in front and tack them low. When dry, cut firm leather to fit the hollow at the back of the long point and hogskin about 1/8 in larger all round; shave both and paste them together.

วัสดุสำหรับขั้นตอนนี้:

หนังหมูฟอกหนังหมูฟอก1 ชิ้น
หนังทำเครื่องม้าหนังทำเครื่องม้า1 ชิ้น
กาวแป้งสาลีกาวแป้งสาลี1 ชิ้น
ตะปูตะปู1 ชิ้น

เครื่องมือที่ต้องใช้:

มีดตัดหนังมีดตัดหนัง
ฟองน้ำฟองน้ำ
คีมปากนกแก้วคีมปากนกแก้ว
ค้อนหงอนค้อนหงอน
7

Welt the skirts and seat

Fit and mark the skirts as for the gentleman's saddle. Put the thin hogskin welt along the upper edge of the seat and stitch skirt and welt together only as far as the root of the big point, and the same opposite under the short point. From there stitch a wider doubled welt to the skirt to the end. Put a narrow welt round the hole cut for the point with a broad welt on it, and a narrow and broad welt under the short point, and stitch the seat to the hogskin piece there. Tack the ends round the long point neatly under the skirt on the near side.

วัสดุสำหรับขั้นตอนนี้:

หนังหมูฟอกหนังหมูฟอก1 ชิ้น
หนังแผ่นข้างอานหนังแผ่นข้างอาน1 ชิ้น
ด้ายหนังด้ายหนัง1 ชิ้น
ขี้ผึ้งช่างรองเท้าขี้ผึ้งช่างรองเท้า1 ชิ้น

เครื่องมือที่ต้องใช้:

มีดตัดหนังมีดตัดหนัง
เหล็กหมาด (สว่านเจาะรูมือ)เหล็กหมาด (สว่านเจาะรูมือ)
เข็มเย็บอานม้าสองเล่มเข็มเย็บอานม้าสองเล่ม
8

Fit the cover to the head

Remove the long-point cover, put a small welt round the back piece, cover it with hogskin and stitch the cover to it all round without stretching or pleating. Turn the cover inside out, damp it, slip it down over the point and nick the bottom so it sits flat on the seat. Paste between the back piece and the point and press it hard into the hollow; hold it with two or three thicknesses of soft brown leather and a soft rag rolled round until the paste dries. Nail the back piece to the tree at the bottom with two or three tacks out of sight, and cut and stitch the pleats in the seat behind the cantle.

วัสดุสำหรับขั้นตอนนี้:

หนังหมูฟอกหนังหมูฟอก1 ชิ้น
กาวแป้งสาลีกาวแป้งสาลี1 ชิ้น
หนังแกะเบซิลหนังแกะเบซิล1 ชิ้น
เศษผ้าฝ้ายเศษผ้าฝ้าย1 ชิ้น
ตะปูตะปู1 ชิ้น
ด้ายหนังด้ายหนัง1 ชิ้น
ขี้ผึ้งช่างรองเท้าขี้ผึ้งช่างรองเท้า1 ชิ้น

เครื่องมือที่ต้องใช้:

มีดตัดหนังมีดตัดหนัง
ฟองน้ำฟองน้ำ
เหล็กหมาด (สว่านเจาะรูมือ)เหล็กหมาด (สว่านเจาะรูมือ)
เข็มเย็บอานม้าสองเล่มเข็มเย็บอานม้าสองเล่ม
ค้อนหงอนค้อนหงอน
9

Put the seat on the tree

Cover the points running to the panel pockets with thin hogskin or basil, as for the gentleman's saddle. Damp the seat, nail it in front and then at the back, tightening it well round the sides. Nail the hogskin piece behind the short point and pull the welt seam exactly along the edge. Draw the skirt points tightly forward with a tack in the end, the skirt edges under the points; cover the nails and leather ends there, and cut the waste close to the nails all round.

วัสดุสำหรับขั้นตอนนี้:

หนังหมูฟอกหนังหมูฟอก1 ชิ้น
ตะปูอานตะปูอาน1 ชิ้น
ตะปูตะปู1 ชิ้น

เครื่องมือที่ต้องใช้:

ฟองน้ำฟองน้ำ
คีมปากนกแก้วคีมปากนกแก้ว
ค้อนหงอนค้อนหงอน
มีดตัดหนังมีดตัดหนัง
10

Make the near-side flap and bolstered safe

Cut the near-side flap and safe (Fig. 7) as two pieces joined in a straight line, the point side in front: the back part like a saddle flap but a little fuller at the bottom, reaching no farther than the end of the saddle-bar front; the safe running a little beyond the centre at the top. Join them with a closing stitch in strong black wax thread, crossing it every six or seven stitches. For the bolstered safe, cut hogskin the size of the safe plus 1 in all round, quilt and mark it with a small single crease in a regular pattern, and press a design into it. Line it with calico stitched along every mark with white or yellow silk or linen thread, outer lines first, flat and without puckers, pricking a hole in every space. Stuff each space with very fine flock cut small, just enough to show the pattern and feel soft. Fit the cover edge to edge on the safe, crease and prick its edge very fine, stitch the straight edge wrong side out over the joint, turn it over and stitch round the edge double-handed. Paste hogskin on the flap part and stitch it round.

วัสดุสำหรับขั้นตอนนี้:

หนังแผ่นข้างอานหนังแผ่นข้างอาน1 ชิ้น
หนังหมูฟอกหนังหมูฟอก1 ชิ้น
ผ้าดิบแคลิโกผ้าดิบแคลิโก1 ชิ้น
ใยขนแกะสำหรับยัดใยขนแกะสำหรับยัด1 ชิ้น
ด้ายลินินด้ายลินิน1 ชิ้น
ด้ายหนังด้ายหนัง1 ชิ้น
ขี้ผึ้งช่างรองเท้าขี้ผึ้งช่างรองเท้า1 ชิ้น
กาวแป้งสาลีกาวแป้งสาลี1 ชิ้น

เครื่องมือที่ต้องใช้:

มีดตัดหนังมีดตัดหนัง
เครื่องมือกรีดพับเครื่องมือกรีดพับ
หัวพ่นไฟโพรเพนหัวพ่นไฟโพรเพน
สิ่วตอกรูหนังสิ่วตอกรูหนัง
กรรไกรกรรไกร
เหล็กหมาด (สว่านเจาะรูมือ)เหล็กหมาด (สว่านเจาะรูมือ)
เข็มเย็บอานม้าสองเล่มเข็มเย็บอานม้าสองเล่ม
11

Fit the off-side flap and both flaps

The off-side flap is small, exactly as for a gentleman's saddle but fuller in the rounds below. Make a gullet piece from the front end of the flap to a little over the centre at the top, to be covered by the point of the safe. Nail the off-side flap underneath from the point backwards and above the point in front, and the near-side safe and flap the same way. Where the web hangs down for the straps, punch a hole in the front of the safe close by the tree and near the end of the flap, and turn that part of the flap to the point under the tree, nailing it along the gullet. The girth straps go on the web.

วัสดุสำหรับขั้นตอนนี้:

หนังแผ่นข้างอานหนังแผ่นข้างอาน1 ชิ้น
ตะปูตะปู1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องเจาะรูหนังเครื่องเจาะรูหนัง
ค้อนหงอนค้อนหงอน
มีดตัดหนังมีดตัดหนัง
12

Make the leather girth

Make the thin brown leather girth, which a gentleman's saddle does not have: 3-1/2 ft long and 2 in wide, with a 1 in roller buckle at one end on a chape cut slanting from both sides to its width. Make a loop for it and another about 6 in lower for the overlap of the strap. Cut another piece 1 ft by 2 in with a strap 1 ft 6 in by 1 in stitched to one end; edge and rub the borders and make a narrow hot crease near the edge. Put two rows of cross-stitching on the near side of the girth and two on the off side. It buckles the reverse way to the usual, so it can be adjusted with the rider in the saddle.

วัสดุสำหรับขั้นตอนนี้:

หนังแกะเบซิลหนังแกะเบซิล1 ชิ้น
หัวเข็มขัดมีลูกกลิ้งหัวเข็มขัดมีลูกกลิ้ง1 ชิ้น
ด้ายหนังด้ายหนัง1 ชิ้น
ขี้ผึ้งช่างรองเท้าขี้ผึ้งช่างรองเท้า1 ชิ้น

เครื่องมือที่ต้องใช้:

มีดตัดหนังมีดตัดหนัง
เครื่องมือกรีดพับเครื่องมือกรีดพับ
หัวพ่นไฟโพรเพนหัวพ่นไฟโพรเพน
แท่งขึ้นรูปห่วงสายแท่งขึ้นรูปห่วงสาย
เหล็กหมาด (สว่านเจาะรูมือ)เหล็กหมาด (สว่านเจาะรูมือ)
เข็มเย็บอานม้าสองเล่มเข็มเย็บอานม้าสองเล่ม
เครื่องเจาะรูหนังเครื่องเจาะรูหนัง
ตลับเมตรตลับเมตร
13

Nails and panel

Place the tough nails as on a gentleman's saddle: one at each skirt point in front, one through each flap at the point, and one on each side at the narrow end of the skirts behind. Make the panel as in chapter II but slightly wider, to go under the safe in front, and fill the near side rather more.

วัสดุสำหรับขั้นตอนนี้:

ตะปูอานตะปูอาน1 ชิ้น
หนังแกะเบซิลหนังแกะเบซิล1 ชิ้น
ผ้าเสิร์จขนสัตว์ผ้าเสิร์จขนสัตว์1 ชิ้น
ใยขนแกะสำหรับยัดใยขนแกะสำหรับยัด1 ชิ้น
ด้ายลินินด้ายลินิน1 ชิ้น

เครื่องมือที่ต้องใช้:

ค้อนหงอนค้อนหงอน
เหล็กหมาด (สว่านเจาะรูมือ)เหล็กหมาด (สว่านเจาะรูมือ)
เข็มเย็บอานม้าสองเล่มเข็มเย็บอานม้าสองเล่ม
เหล็กเกลี่ยที่นั่งเหล็กเกลี่ยที่นั่ง
14

Troubleshooting

Side saddle troubleshooting.

Flow

Loading...
15

History and honest limits

From **Saddlery**, edited by Paul N. Hasluck, David McKay, 1904 (archive.org saddlery00hasl), chapter III, "Ladies' Side Saddles", pp. 26-35, Figs. 6-8; every fraction was read on the scan. He gives few sizes of his own here and refers to the gentleman's saddle (chapters I-II) for the web, seat, skirts and panel, as this blueprint does. The leaping head (Fig. 8), quilted skirts, glove pocket (about 4-1/2 by 3-1/2 in) and girth cross straps are not made here. The tools and metric figures are ours.

วัสดุ

19

เครื่องมือที่จำเป็น

14

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...