ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Counter-Turning Hooped Beater Churn: One Bevel Wheel Turns a Spindle and a Hollow Shaft Opposite Ways, Spiral Hoops Sweep the Wall
Buttercup

สร้างโดย

Buttercup

11. พฤศจิกายน 2026IE
10
0
0
0
0

Counter-Turning Hooped Beater Churn: One Bevel Wheel Turns a Spindle and a Hollow Shaft Opposite Ways, Spiral Hoops Sweep the Wall

William Bently Hopkins of Oakfield, New York, received US 31,806, dated 26 March 1861, for a churn whose crank turns one bevel wheel between two pinions, one above and one below, so a spindle and a hollow shaft round it turn opposite ways. The spindle carries two slats; the hollow shaft carries a slat at its foot and, through two hoops that spiral a quarter turn down beside the wall, a second slat between the spindle's two. The hoops sweep back the cream that would lodge against the wall. The cover lifts off with the gearing and the beaters come out. The patent gives no sizes; every size here is ours.
ระดับกลาง
About 2 days

คำแนะนำ

1

Two sets turning against each other

กำลังโหลดสมุด Jupyter…
2

Parts turning opposite ways in one churn, a year before

Ward turns a ribbed cylinder one way and dashers the other. Hopkins turns two sets of beaters on a spindle and a hollow shaft from one bevel wheel.
3

Read US 31,806

"The hoops n n ... not only maintain the relative position between k and m, but have a specific effect in displacing and agitating that portion of the milk or cream which would, by the operation of the two sets of beaters, be forced and impacted against the walls of the vessel, where they would, if allowed to remain, escape the action of the beaters, to a considerable extent."
4

Print the step

The step on the bucket's floor: 40 mm across, 12 high, with a 12.8 mm hole 8 deep. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
5

Body A and cover B

Use a 20-litre food-grade bucket as the body A and set the printed step in the middle of its floor. Cut a 12 mm HDPE cover B to its top, bore it 23 mm at the centre, and saw it across through the hole into two halves.

วัสดุสำหรับขั้นตอนนี้:

ถังขนาด 20 ลิตรถังขนาด 20 ลิตร1 ชิ้น
แผ่น HDPEแผ่น HDPE1 ชิ้น
เส้นใย PETGเส้นใย PETG1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เข็มทิศเข็มทิศ
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
สว่านไร้สายสว่านไร้สาย
6

Spindle G and slats j

Cut a 12 mm stainless spindle G 580 mm long. Plane two hardwood slats j 220 x 30 x 8 mm, bore each 12.2 mm at the middle with a hardwood hub, and pin them on the spindle 30 and 130 mm above its foot, a quarter turn apart, each tilted 20 degrees about its length.

วัสดุสำหรับขั้นตอนนี้:

แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้กาวไม้1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
7

Hollow shaft H, slats k and m, hoops n

Cut a 22 mm stainless tube H 270 mm long. Plane two hardwood slats k and m 250 x 30 x 8 mm, tilted 20 degrees the other way. Fix k on the tube's foot with a hardwood hub. Bore m 13.2 mm at its hub so it turns loose on the spindle, and slide it on between the two j slats. Bend two strips of stainless strip 20 mm wide into hoops n that run a quarter turn round at 124 mm radius while dropping 100 mm, and screw each from an end of k down to the end of m a quarter turn round, so m lies at right angles to k. Slide the tube down over the spindle.

วัสดุสำหรับขั้นตอนนี้:

ท่อสเตนเลสท่อสเตนเลส1 ชิ้น
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
แถบเหล็กกล้าไร้สนิมรีดเย็น (420)แถบเหล็กกล้าไร้สนิมรีดเย็น (420)1 ชิ้น
สกรูไม้สกรูไม้8 ชิ้น
กาวไม้กาวไม้1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ค้อนยางค้อนยาง
ชุดไขควงชุดไขควง
8

Print the pinion f

The lower pinion f on the hollow shaft: 14 teeth, module 2.5, 22.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
9

Print the pinion e

The upper pinion e on the spindle: 14 teeth, module 2.5, 12.2 mm bore; fit it hub up. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
10

Print the driving wheel C

The driving wheel C: a crown wheel of 42 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
11

Frame, wheel C, pinions e and f, crank D

Screw two hardwood posts 30 x 40 mm, 195 tall, to the cover either side of its centre, 150 mm apart over their inner faces, and join their tops with a top bar bored 12.6 mm over the centre. Screw two hardwood bearing blocks 50 x 25 mm, 120 tall, to the cover 60 and 125 mm in front of the centre, bored 16.6 mm across 96 mm above the cover. Pin the pinion f on the hollow shaft 40 mm above the cover and the pinion e on the spindle 105 mm above f, teeth facing each other. Run a 16 mm stainless shaft 150 mm long through the blocks with the crown wheel C pinned on its inner end between the two pinions, meshing both, a shaft collar, and a crank D of mild steel flat bar, 100 mm throw, with a hardwood handle.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น
Shaft CollarShaft Collar1 ชิ้น
สลักผ่าสลักผ่า4 ชิ้น
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น
สกรูไม้สกรูไม้12 ชิ้น
เส้นใย PETGเส้นใย PETG1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ชุดไขควงชุดไขควง
12

The build in 3D

FreeCAD model of this build, the bucket cut open: the step, the spindle with its two slats, the hollow shaft with its slat, the loose slat and the two spiral hoops, the cover, posts and top bar, the crown wheel between the two pinions, and the crank.
ไฟล์แบบBLENDCC0 - Free
13

Churn

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket with the beaters in, lay on the cover halves and seat the gearing. Turn the crank steadily, timing it. When the butter comes, lift off the cover and gearing, lift out the beaters, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

วัสดุสำหรับขั้นตอนนี้:

ครีมสดครีมสด10 l
เกลือทะเลเม็ดหยาบเกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เทอร์มอมิเตอร์หัววัดแบบเสียบค้างเทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลานาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัวเครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่ชามผสมสเตนเลสใบใหญ่
14

Troubleshooting

Hooped-beater churn troubleshooting.

Flow

Loading...
15

History and honest limits

**Wm. Bently Hopkins** of Oakfield, Genesee County, New York, US 31,806, 26 March 1861, "Churn". He claimed "the beaters j j and k, m, the latter provided with spiral arms, n n", and did not claim beaters on separate shafts turning opposite ways as such. His text says the hoops run a quarter of the circle, putting m at right angles to k, and also that m is forty-five degrees in advance of k; we follow the hoops. His gearing was a bevel wheel between two bevel pinions; ours is a printed crown wheel. The patent gives no sizes; every size here is ours.

วัสดุ

16

เครื่องมือที่จำเป็น

17

ไฟล์ออกแบบ

5

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...