การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Industrial Air Compressor: a Converted Motorcycle Engine, Motor-Driven (Shop Notes, 1919)
Emma

สร้างโดย

Emma

4. พฤศจิกายน 2026SE
9
0
0
0
0

Industrial Air Compressor: a Converted Motorcycle Engine, Motor-Driven (Shop Notes, 1919)

A workshop compressor driven by a 1 hp electric motor: an old single-cylinder motorcycle engine rebored and run as a pump, its exhaust port blanked, its own automatic inlet valve taking in air, and a ball check valve in the spark-plug hole sending air to a tank. Source: Popular Mechanics Shop Notes for 1919, pp. 3166-3167. Unknown: tank, belt and sizes. Picture: the article's drawing.
ระดับกลาง
Unknown

คำแนะนำ

1

Recondition the cylinder

Rebore the old engine and fit a new piston for good compression. Remove the exhaust valve and bolt a steel plate, with a gasket under it, over the exhaust port. Leave the automatic inlet valve as it is: it now draws in air.

วัสดุสำหรับขั้นตอนนี้:

วัสดุที่ไม่ทราบวัสดุที่ไม่ทราบ1 old motorcycle engine
ชุดลูกสูบและก้านสูบชุดลูกสูบและก้านสูบ1 new piston
แผ่นเหล็กกล้าละมุนแผ่นเหล็กกล้าละมุน1 blanking plate
ปะเก็นกันรั่วปะเก็นกันรั่ว1 ชิ้น
สลักเกลียวหัวหกเหลี่ยม - เกรด 8.8สลักเกลียวหัวหกเหลี่ยม - เกรด 8.81 ชิ้น

เครื่องมือที่ต้องใช้:

ก้านคว้านรูก้านคว้านรู
เครื่องกลึงโลหะเครื่องกลึงโลหะ
สว่านมือสว่านมือ
ประแจเลื่อนประแจเลื่อน
2

Fit the outlet

In place of the priming cock on top of the cylinder (the drawing shows it screwed into the spark-plug hole) fit a ball-valve hose connection, and run its hose to the air tank.

วัสดุสำหรับขั้นตอนนี้:

วาล์วกันกลับแบบลูกบอลวาล์วกันกลับแบบลูกบอล1 ชิ้น
สายลมสายลม1 ชิ้น
วัสดุที่ไม่ทราบวัสดุที่ไม่ทราบ1 air tank

เครื่องมือที่ต้องใช้:

ประแจเลื่อนประแจเลื่อน
3

Fit the drive and mount it

Fit a longer main shaft and key an ordinary shaft pulley on its end. Leave the old flywheel in place for momentum. Bolt steel lugs to the floor and fasten the engine base to them. Belt it to a 1 hp, 110 volt motor, and put oil in the crankcase for splash lubrication.

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กกลมคาร์บอนต่ำแท่งเหล็กกลมคาร์บอนต่ำ1 longer main shaft
รอกรอก1 ชิ้น
แผ่นเหล็กกล้าละมุนแผ่นเหล็กกล้าละมุน1 floor lugs
สลักเกลียวหัวหกเหลี่ยม - เกรด 8.8สลักเกลียวหัวหกเหลี่ยม - เกรด 8.81 ชิ้น
มอเตอร์ไฟฟ้ามอเตอร์ไฟฟ้า1 1 hp, 110 V
น้ำมันเครื่องจักรน้ำมันเครื่องจักร1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
ประแจเลื่อนประแจเลื่อน

วัสดุ

11

เครื่องมือที่จำเป็น

4

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...