การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Kitchen Funnel with Air-Vent Ribs, 3D Printed in PETG
3DBonanza

สร้างโดย

3DBonanza

18. พฤศจิกายน 2026US
1
0
0
0
0

Kitchen Funnel with Air-Vent Ribs, 3D Printed in PETG

A 120 mm kitchen funnel for bottling wine, cider or juice, printed in one piece in PETG. Three small ribs along the outside of the spout hold it off the bottle neck so air can come out while the liquid goes in, so it pours without glugging. A common, open design; all sizes are ours, and we have not printed or tested it yet.
เริ่มต้น
About 4 hours, mostly printing

คำแนะนำ

1

Our funnel's numbers

กำลังโหลดสมุด Jupyter…
2

Make it fit your bottles

Optional: change TOP_D or the spout sizes and run it in FreeCAD: OUT=. TOP_D= freecadcmd build_all.py
build_all.pypython
"""Batch 2451 -- PETG kitchen funnel with air-vent ribs on the spout. Open, common design (Admiral 2026-11-18: "it is open knowledge on
what a funnel is"); all sizes ours. Run: OUT=<dir> [TOP_D=120] freecadcmd build_all.py  (mm; printed rim-down on the bed, no supports)."""
import math, os
import FreeCAD as App, Part, MeshPart
OUT = os.environ["OUT"]
V = App.Vector
TOP_D = float(os.environ.get("TOP_D", "120"))     # rim inside diameter
WALL = 1.8
CONE_HALF = 30.0                                   # half-angle: 60 degree cone
SPOUT_TOP_D, SPOUT_TIP_D, SPOUT_L = 16.0, 13.0, 50.0   # spout outside, tapering so it fits bottle necks
RIB_H, RIB_W = 1.2, 1.6                            # three vent ribs on the spout's outside
RIM_LIP = 4.0                                      # flat lip round the rim (bed adhesion, stiffness)
r_top = TOP_D / 2
r_neck_in = SPOUT_TOP_D / 2 - WALL
cone_h = (r_top - r_neck_in) / math.tan(math.radians(CONE_HALF))
def save(sh, name):
    bb = sh.BoundBox
    print(name, "valid", sh.isValid(), "solids", len(sh.Solids), "bbox", [round(v, 1) for v in (bb.XLength, bb.YLength, bb.ZLength)],
          "volume_cm3", round(sh.Volume / 1000, 1))
    MeshPart.meshFromShape(Shape=sh, LinearDeflection=0.03, AngularDeflection=0.12).write(os.path.join(OUT, name + ".stl"))
# z up: spout tip at z=0, cone above, rim at the top
off = WALL / math.cos(math.radians(CONE_HALF))
outer = Part.makeCone(SPOUT_TOP_D / 2, r_top + off, cone_h, V(0, 0, SPOUT_L))
inner = Part.makeCone(r_neck_in, r_top, cone_h + 0.01, V(0, 0, SPOUT_L))
spout_o = Part.makeCone(SPOUT_TIP_D / 2, SPOUT_TOP_D / 2, SPOUT_L + 0.01, V(0, 0, 0))
spout_i = Part.makeCone(SPOUT_TIP_D / 2 - WALL, r_neck_in, SPOUT_L + 0.02, V(0, 0, -0.01))
body = outer.fuse(spout_o).cut(inner).cut(spout_i)
lip = Part.makeCylinder(r_top + off + RIM_LIP, 1.6, V(0, 0, SPOUT_L + cone_h - 1.6)).cut(Part.makeCylinder(r_top - 0.5, 3, V(0, 0, SPOUT_L + cone_h - 2)))
body = body.fuse(lip)
r_at = lambda z: (SPOUT_TIP_D + (SPOUT_TOP_D - SPOUT_TIP_D) * z / SPOUT_L) / 2
for a in (0, 120, 240):
    z0, z1 = 2.0, SPOUT_L - 1.0
    pts = [V(r_at(z0) - 0.4, -RIB_W / 2, z0), V(r_at(z0) + RIB_H, -RIB_W / 2, z0), V(r_at(z1) + RIB_H, -RIB_W / 2, z1), V(r_at(z1) - 0.4, -RIB_W / 2, z1)]
    rib = Part.Face(Part.makePolygon(pts + [pts[0]])).extrude(V(0, RIB_W, 0))
    rib.rotate(V(0, 0, 0), V(0, 0, 1), a)
    body = body.fuse(rib)
body = body.removeSplitter()
save(body, "petg-kitchen-funnel")
cap = math.pi * cone_h / 3 * (r_top**2 + r_top * r_neck_in + r_neck_in**2) / 1000
print("cone height", round(cone_h, 1), "mm; holds about", round(cap), "ml in the cone")
print("spout", SPOUT_TOP_D, "->", SPOUT_TIP_D, "mm outside, bore", round(SPOUT_TIP_D - 2 * WALL, 1), "mm at the tip")
print("air gap per rib, in a neck the spout just fits:", RIB_H, "x", "(gap between ribs)")

เครื่องมือที่ต้องใช้:

เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
3

Print the funnel

Print it rim down on the bed, no supports; the cone and spout grow upward. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 3 walls.
ไฟล์แบบSTLCC0 - Free

วัสดุสำหรับขั้นตอนนี้:

เส้นใย PETGเส้นใย PETG60 ก.

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
ชุดหัวฉีดเครื่องพิมพ์ 3 มิติชุดหัวฉีดเครื่องพิมพ์ 3 มิติ
4

Clean it up

Trim any strings or blobs, especially inside the spout and between the ribs. Check the spout is clear.

เครื่องมือที่ต้องใช้:

มีดคัตเตอร์งานประดิษฐ์มีดคัตเตอร์งานประดิษฐ์
5

Check the fit

Put the spout into a bottle: the ribs should touch the neck and leave gaps between them. Pour water through and watch it run without glugging.
ขั้นตอนที่ 5 - Image 1

เครื่องมือที่ต้องใช้:

ขวดแก้วพร้อมจุกขวดแก้วพร้อมจุก
น้ำน้ำ
6

Sanitise

Soak it in no-rinse sanitiser mixed as its label says. Do not boil it: PETG softens at about 80 °C.

เครื่องมือที่ต้องใช้:

น้ำยาฆ่าเชื้อน้ำยาฆ่าเชื้อ
น้ำน้ำ
7

Troubleshooting

Funnel problems and fixes.

Flow

Loading...
8

Honest limits

A common, open design, drawn by us in FreeCAD; every size is ours. The ribs were checked by slicing the model; the funnel has not been printed or poured through by us yet. Sanitise before every use and replace it when scratched.

วัสดุ

1
  • ตัวยึดตำแหน่ง

เครื่องมือที่จำเป็น

7

ไฟล์ออกแบบ

1

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...