การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Trick Lariat That Will Not Twist: Brass Swivels in the Rope and a Choker on the Hondoo (La Rue, 1935)
Tex

สร้างโดย

Tex

13. พฤศจิกายน 2026FO
11
0
0
0
0

Trick Lariat That Will Not Twist: Brass Swivels in the Rope and a Choker on the Hondoo (La Rue, 1935)

Richard L. La Rue of Los Angeles received US 1,993,010, dated 5 March 1935, for a lariat that beginners can spin. A spinning loop twists the rope; an expert lets it roll in the hand, a beginner cannot. La Rue cuts the rope into sections joined by small brass swivels, so the twist runs out. The hondoo, the eye the rope runs through, is clamped in a brass ferrule, and a wire choker can lock the loop at one size. We make it from cotton rope and brass tube. All sizes are ours.
ระดับกลาง
About 4 hours

คำแนะนำ

1

Where the swivels go

กำลังโหลดสมุด Jupyter…
2

Read US 1,993,010

"In accordance with the present invention, twisting of the rope is prevented by inserting several swivels at intervals along the rope, so that no matter how the operator holds it there is always at least one swivel between his hand and the loop. The swivels are made substantially the same outside diameter as the rope so that they pass readily through the hondoo."
3

Cut the rope

Cut 6 m of 10 mm braided cotton rope (ours) into the sections the notebook gives. Wrap tape round each place before cutting so the ends do not fray.

วัสดุสำหรับขั้นตอนนี้:

เชือกฝ้ายตีเกลียวเชือกฝ้ายตีเกลียว1 ชิ้น

เครื่องมือที่ต้องใช้:

ตลับเมตรตลับเมตร
มีดคัตเตอร์งานประดิษฐ์มีดคัตเตอร์งานประดิษฐ์
4

Make the ferrules

For three swivels cut six 25 mm pieces of 3/8 in brass tube (ours), his ferrules 6, and file the ends square. Soften the brass by heating each piece to a dull red with the torch and dropping it in water. On the anvil, tap one end of each inward all round with the hammer, turning it as you go, until the opening is about 4.5 mm: his end wall 7. Flare the other end out a little so the rope will go in.

วัสดุสำหรับขั้นตอนนี้:

ท่อทองเหลือง เส้นผ่านศูนย์กลางนอก 9.5 มม.ท่อทองเหลือง เส้นผ่านศูนย์กลางนอก 9.5 มม.1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ชุดตะไบชุดตะไบ
หัวพ่นไฟโพรเพนหัวพ่นไฟโพรเพน
ถังชุบน้ำถังชุบน้ำ
น้ำน้ำ
ทั่งทั่ง
ค้อนหัวกลมค้อนหัวกลม
แว่นนิรภัยแว่นนิรภัย
5

Join the ferrules into swivels

Cut three 10 mm pieces of 4 mm brass tube (ours), his member 8. Put two ferrules end wall to end wall, push the small tube through both openings, and flare its ends with a centre punch from inside each ferrule until they cannot pull back through: his flanges 9. The two halves must turn freely on each other.

วัสดุสำหรับขั้นตอนนี้:

ท่อทองเหลืองท่อทองเหลือง1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
เหล็กตอกนำศูนย์เหล็กตอกนำศูนย์
ค้อนหัวกลมค้อนหัวกลม
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
6

Fit the rope into the swivels

Push a rope end into each open ferrule as far as it goes. Squeeze the flared end back in, with the hammer on the anvil or in the vice, until it digs into the rope all round. Pull hard on each joint to test it.

เครื่องมือที่ต้องใช้:

ค้อนหัวกลมค้อนหัวกลม
ทั่งทั่ง
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
7

Make the hondoo

Cut 40 mm of brass tube big enough to take the rope doubled (ours) and saw it open along its length. Squeeze one end round the single rope; flatten the other end into an oval. Pass the loop end of the rope through, from the small end, then double its butt end back and push it into the oval end as far as it will go, leaving a small eye: his hondoo 3. Dent the oval end to hold the butt (his 14) and turn one cut edge in against the rope (his 15).

วัสดุสำหรับขั้นตอนนี้:

ท่อทองเหลืองท่อทองเหลือง1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
คีมปากแบนคีมปากแบน
เหล็กตอกนำศูนย์เหล็กตอกนำศูนย์
ค้อนหัวกลมค้อนหัวกลม
8

Bend the choker

Bend 2.5 mm steel wire (ours) into a figure 8 round the two rope parts of the hondoo, one eye on each, so it slides when pushed but stays put by friction. Pass the free end of the rope through the hondoo to make the loop.

วัสดุสำหรับขั้นตอนนี้:

ลวดเหล็กลวดเหล็ก1 ชิ้น

เครื่องมือที่ต้องใช้:

คีมตัดลวดปากเฉียงคีมตัดลวดปากเฉียง
คีมปากกลมคีมปากกลม
คีมปากแบนคีมปากแบน
9

Use it

With the choker pushed up to the ferrule, the rope runs freely through the hondoo like any lariat. To spin a loop of one size, slide the choker away from the ferrule until the hondoo grips the running rope: the loop then stays the same size while it spins.
10

Troubleshooting

Swivel trick lariat troubleshooting.

Flow

Loading...
11

History and honest limits

**Richard L. La Rue** of Los Angeles, US 1,993,010, dated 5 March 1935, filed 16 November 1932, for "a lariat for use by amateurs in performing tricks". He claimed the choker, "a figure 8 clamp of heavy wire", and a clamp "movable back and forth over the doubled rope constituting the hondoo for varying the size of the eye". He also shows a second choker of bent wire (Fig. 6), not built here. He names no rope and gives no sizes: the cotton rope, its length, the tubes, the annealing, the wire and all sizes are ours.

วัสดุ

4

เครื่องมือที่จำเป็น

15

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...