ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Liquid Hydrogen: Gas at 200 Atmospheres Cooled by Dry Ice and Liquid Air, then Expanded in a Regenerator Coil (Travers, 1901)
Charlie

สร้างโดย

Charlie

1. พฤศจิกายน 2026DE
7
0
0
0
0

Liquid Hydrogen: Gas at 200 Atmospheres Cooled by Dry Ice and Liquid Air, then Expanded in a Regenerator Coil (Travers, 1901)

Hydrogen will not cool when it expands at room temperature, so Travers first chilled it with dry ice and then with liquid air boiling under a vacuum. Only then did expansion through a fine valve inside a regenerator coil cool it further, until clear liquid hydrogen ran into a vacuum vessel. Result: liquid hydrogen (specific gravity 0.06), cold enough to freeze air solid. Source: M. W. Travers, The Experimental Study of Gases (1901), pp. 196-206. Hydrogen is flammable; liquid air and liquid hydrogen are extremely cold. Picture: Fig. 103 of the book.
ขั้นสูง
1 week

คำแนะนำ

1

Make and store the hydrogen

Put about 40 lb of commercial granulated zinc in a beer cask with a tap funnel, a delivery tube, an escape pipe into a vessel of water (safety valve) and a stoneware cock at the bottom to draw off spent acid. Run in dilute sulphuric acid. When the air is out, pass the gas through a wash-bottle of potassium permanganate into the gasometer (sheet iron, 6 ft high, 5 ft 6 in across, over water first saturated with hydrogen). Wash the gasometer out with hydrogen before collecting the main quantity. This takes five hours.

วัสดุสำหรับขั้นตอนนี้:

ไฮโดรเจนไฮโดรเจน1 a gasometer full, made here

เครื่องมือที่ต้องใช้:

สังกะสีสังกะสี
กรดซัลฟิวริกเจือจางกรดซัลฟิวริกเจือจาง
ถังไม้ถังไม้
กรวยหยดกรวยหยด
โพแทสเซียมเปอร์แมงกาเนตโพแทสเซียมเปอร์แมงกาเนต
ขวดล้างแก๊สขวดล้างแก๊ส
ถังเก็บแก๊สถังเก็บแก๊ส
น้ำน้ำ
2

Make liquid air and ready the compressor

In the two or three days before, use the compressor to make liquid air with the Hampson liquefier and store it in vacuum vessels, about 8 litres in all. Then take the compressor apart and check the valves, springs and fibre packings. Remove the Hampson machine and connect the compressor through the cylinder of caustic potash to the hydrogen liquefier.

เครื่องมือที่ต้องใช้:

เครื่องอัดก๊าซเครื่องอัดก๊าซ
เครื่องทำอากาศเหลวแบบแฮมป์สันเครื่องทำอากาศเหลวแบบแฮมป์สัน
อากาศเหลวอากาศเหลว
ภาชนะสุญญากาศ (ดิวอาร์)ภาชนะสุญญากาศ (ดิวอาร์)
3

Cool the liquefier

Four people are needed. Pack the vessel round coil A with solid carbonic acid and alcohol (-80 °C). Pour liquid air into chamber B and let it into chamber C, pumped down to 100 mm of mercury so it boils below -200 °C. Draw liquid air into vacuum vessel H and boil it under reduced pressure to chill the regenerator coil below -200 °C, then let it out and put vessels K and M (with a little liquid air) back in place.

เครื่องมือที่ต้องใช้:

เครื่องทำไฮโดรเจนเหลวเครื่องทำไฮโดรเจนเหลว
คาร์บอนไดออกไซด์ของแข็งคาร์บอนไดออกไซด์ของแข็ง
เอทานอลแปลงสภาพ 95 %เอทานอลแปลงสภาพ 95 %
อากาศเหลวอากาศเหลว
ภาชนะสุญญากาศ (ดิวอาร์)ภาชนะสุญญากาศ (ดิวอาร์)
ปั๊มสุญญากาศปั๊มสุญญากาศ
เกจวัดสุญญากาศเกจวัดสุญญากาศ
4

Compress the hydrogen to 200 atmospheres

Purge the air from the compressor: open cock a, run a few turns, stop and open cock rho; do this three or four times. Then raise the pressure. The first cylinder takes the gas to about 16 atm, with a little glycerol and water holding 5 % caustic soda as lubricant; the second takes it to about 200 atm. The water is separated out and the gas dried over lumps of solid caustic potash. Have it at 200 atm by the time the liquefier is cold.

เครื่องมือที่ต้องใช้:

เครื่องอัดก๊าซเครื่องอัดก๊าซ
กลีเซอรอลกลีเซอรอล
โซดาไฟ (โซเดียมไฮดรอกไซด์)โซดาไฟ (โซเดียมไฮดรอกไซด์)
น้ำน้ำ
โพแทสเซียมไฮดรอกไซด์โพแทสเซียมไฮดรอกไซด์
เกจวัดความดันเกจวัดความดัน
5

Expand and collect the liquid

Reconnect chamber C to the exhaust pump and let liquid air in slowly (a fall of the mercury in the vacuum gauge means too fast). Open the expansion valve with the milled nut; let the gas out through the water tank for a few moments to clear the air, then open cock i so it circulates back. Keep B and the coil-A vessel topped up. Watch the glycerol gauge for the flow and turn the milled nut slowly back and forth the whole time so it does not block. H coats with white solid air; open cock r now and then, and the liquid runs through a baize filter into K. Lift K out on its wire into a vessel with a little liquid air. About 10 % of the gas is lost per run.

เครื่องมือที่ต้องใช้:

เครื่องทำไฮโดรเจนเหลวเครื่องทำไฮโดรเจนเหลว
อากาศเหลวอากาศเหลว
คาร์บอนไดออกไซด์ของแข็งคาร์บอนไดออกไซด์ของแข็ง
ภาชนะสุญญากาศ (ดิวอาร์)ภาชนะสุญญากาศ (ดิวอาร์)
ปั๊มสุญญากาศปั๊มสุญญากาศ
เกจวัดสุญญากาศเกจวัดสุญญากาศ
เกจวัดความดันเกจวัดความดัน

วัสดุ

1
  • 1 a gasometer full, made here
    ตัวยึดตำแหน่ง

เครื่องมือที่จำเป็น

21

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...