ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Floating-Breaker Churn: A Propeller Dasher Under a Breaker That Floats in Wall Grooves, a Water Tube Held by the Faucet
Edward Lynch of Buffalo, New York, received US 27,864, dated 10 April 1860, for a churn. Propeller blades at the bottom of an upright crank-driven shaft drive the cream up against a breaker that floats on it: a ring round the shaft with bevelled arms whose ends ride loosely in grooves in the churn's sides, so it keeps its place at the surface for any amount of cream. A flat tube of warm or cold water stands inside, held by the faucet that also draws off the buttermilk.
The patent gives no sizes; every size here is ours.
ระดับกลาง
About 2 days, plus printing
คำแนะนำ
1
1
A breaker that floats
A breaker that floats
กำลังโหลดสมุด Jupyter…
2
2
Paddles under a fixed partition, three weeks before
Paddles under a fixed partition, three weeks before
Sangster's partition is fixed below the cream. Lynch's breaker floats on top of it.
3
3
Read US 27,864
Read US 27,864
"They fit loosely in the grooves, so as to allow the breaker to float, upon the milk or cream, and hence always retain the same relation to the milk or cream, whether there be a large or small quantity in the churn."
4
4
Print the dash blades J
Print the dash blades J
Two-blade propeller 190 mm across, blades 80 x 50 x 5 mm pitched 30 degrees, on a hub bored 16.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the water tube L
Print the water tube L
Flat open-topped tank 160 x 30 mm and 210 deep, 3 mm walls, curved to stand against the bucket's side, with a collar under its foot to hold the faucet's nut. PETG, 0.2 mm layers, 100 % infill; fill it with water and check it holds before use.
6
6
Print the crown wheel
Print the crown wheel
Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Print the pinion
Print the pinion
Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
8
8
Grooves i, breaks K and the faucet M
Grooves i, breaks K and the faucet M
Screw three pairs of hardwood strips 20 x 22 mm, 335 long, upright inside the bucket a third of a turn apart, 24 mm apart in each pair, as the grooves i. Screw two triangular hardwood breaks K, 30 mm deep and 150 tall, to the side near the floor between them, and seal every screw hole outside with silicone. Bore the bucket 22 mm, 30 mm above the floor and opposite the third groove, for the spigot. Set the tank against the side there, pass the spigot through the side and screw it into its nut, set in the tank's collar, so it holds the tank and opens into the churn.
วัสดุสำหรับขั้นตอนนี้:
ถังขนาด 20 ลิตร1 ชิ้น
แผ่นไม้เนื้อแข็ง1 ชิ้น
สกรูไม้16 ชิ้น
ก๊อก PVC1 ชิ้น
เส้นใย PETG1 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยวงเดือนตั้งโต๊ะ
ชุดโฮลซอว์
สว่านไร้สาย
ชุดดอกสว่าน
ชุดไขควง
ประแจเลื่อน
ตลับเมตร9
9
Floating breaker H
Floating breaker H
Cut a hardwood ring 100 mm across with a 60 mm hole and 50 deep. Cut three hardwood arms 20 mm thick and 50 deep, bevelled so the lower edge is 4 mm thick, the bevel facing the opposite way to the propeller's blades, long enough to reach loosely into the grooves; glue and screw them into the ring a third of a turn apart.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้6 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
ชุดโฮลซอว์
สว่านไร้สาย
ชุดดอกสว่าน
กระดาษทราย
แคลมป์แบบบาร์
ชุดไขควง10
10
Shaft B, cover P and gearing
Shaft B, cover P and gearing
Screw a hardwood step 50 x 50 x 6 mm to the floor's centre, bored 17 mm, 5 deep. Cut a 16 mm stainless shaft 465 mm long and turn or file its top 77 mm down to 12 mm; fit the propeller 8 mm above the floor. Cut a cover P of HDPE sheet to lie on the rim, bored 20 mm in the centre. Cut a hardwood cross piece N 350 x 205 x 25 mm with two hardwood fingers O 30 x 30 x 20 mm under it to rest on the cover, bored 13 mm for the shaft; fit the pinion above it, two chairs with a 12 mm crank shaft and the crown wheel, and a hardwood crank D with a dowel handle.
วัสดุสำหรับขั้นตอนนี้:
ท่อนไม้เนื้อแข็ง1 ชิ้น
แท่งสเตนเลส2 ชิ้น
แผ่น HDPE1 ชิ้น
แผ่นไม้เนื้อแข็ง2 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้10 ชิ้น
Shaft Collar2 ชิ้น
สลักผ่า1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
ปากกาจับชิ้นงานหน้าโต๊ะ
เลื่อยจิ๊กซอว์
เลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สาย
ชุดดอกสว่าน
ชุดดอกสว่านใบพาย
ชุดไขควง11
11
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket cut open: the propeller blades J on the shaft, the floating breaker H in its three grooves, the breaks K, the water tube L held by the faucet M, the cover P, the cross piece N with its fingers O, and the crank and gearing.
12
12
Churn
Churn
Pour about 6 litres of heavy cream into the bucket and set the breaker in its grooves; it floats on the cream. Pour warm or cold water from the kettle or tap into the tube L to bring the cream to about 15 °C, checked with the thermometer. Put on the cover, cross piece and gearing, and turn the crank steadily, timing it. When the butter comes, draw the buttermilk off at the faucet into a bowl, lift out the gearing, cover, breaker and butter, wash the butter in cold water until it runs clear, salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด6 l
น้ำ1 ชิ้น
เกลือทะเลเม็ดหยาบ1 ชิ้นเครื่องมือที่ต้องใช้:
กาต้มน้ำไฟฟ้า
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่13
13
Troubleshooting
Troubleshooting
Floating-breaker churn troubleshooting.
Flow
Loading...
14
14
History and honest limits
History and honest limits
**Edward Lynch** of Buffalo, New York, US 27,864, 10 April 1860, "Churn", assigned to himself and Jas. J. McCool. He claimed the floating breaker with its ring, bevelled arms and grooves, and the tube held by the faucet. His tube is metal; ours is printed, and our faucet draws the milk through a collar under the tube's foot, our reading of his double-duty faucet. Every size here is ours.
วัสดุ
16- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 32 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 6 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
20- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
5พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

False-Bottom Jet Churn: Paddles Under a Pierced Partition Draw Cream Down at the Centre and Jet It Up at the Rim
โดย Buttercup
งานไม้
13
0
0
0
0
0

Hot-Water Cylinder Churn: Cream Is Crushed Between a Warm Turning Cylinder and an Adjustable Plate, Then Falls to a Dasher
โดย Buttercup
งานไม้
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
โดย TheChef
งานฝีมือ
63
0
0
0
0
0
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

