ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Pendulum Twin-Dasher Churn: A Swinging Weighted Lever Rocks a Beam That Works Two Half-Dashers Alternately
James O. Merrill of Chichester, New Hampshire, received US 23,986, dated 10 May 1859, for an oscillating churn light enough to be worked by a child. A weighted pendulum behind the frame rocks a shaft; on its front end a beam rocks, and two links from the beam's ends work two dasher arms up and down in turn through slots in a guide bar. Each arm carries a half-round dasher pierced with holes, so the two halves fill the barrel. The two-piece cover is held down by a thumb screw.
This rung builds it full size in timber over a 20-litre bucket.
ระดับกลาง
About 2 days
คำแนะนำ
1
1
How far the dashers move
How far the dashers move
กำลังโหลดสมุด Jupyter…
2
2
Two dashers worked in turn, before it
Two dashers worked in turn, before it
Mitchell's lever worked two dashers in turn; Merrill's weighted pendulum keeps them going with less effort.
3
3
Read US 23,986
Read US 23,986
"... the operator oscillates the lever L, which communicates the motion through the vibrating shaft M, the vibrating lever E, the auxiliary levers F, F', to the dasher arms G, G', thus producing an alternate reciprocating action of the dashers N, N'".
4
4
Base and frame
Base and frame
Cut a pine base A 720 x 520 mm. Stand two side pieces B B' of 44 x 70 mm timber 960 mm tall, 400 mm apart, 200 mm from the base's back edge, with diagonal side braces I I' and front braces H H' to the base. Screw top braces C C' (444 x 60 x 22 mm) across the front and back faces of the side pieces at the top, and bore both 21 mm in the middle, 30 mm below their top edge.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้สน2 ชิ้น
ไม้เนื้ออ่อน 70x70 มม.4 ชิ้น
สกรูไม้ #10 x 3"30 ชิ้น
กาวไม้1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยมือ
สว่านไร้สาย
ชุดดอกสว่านใบพาย
แคลมป์
ระดับน้ำ
ตลับเมตร5
5
Shaft M, lever E and pendulum L
Shaft M, lever E and pendulum L
Screw a hardwood bearing block 80 x 80 x 18 mm, bored 20.5 mm, over each hole. Cut a 20 mm steel shaft 310 mm long and pass it through both. On its front end fix a hardwood lever E 400 x 60 x 20 mm at its middle with a bolt across, drilled 8.5 mm 150 mm each side of the middle for the pins c. On its back end fix the pendulum L, a hardwood bar 50 x 20 mm, 810 mm long, 60 mm below its top. Glue a 24 mm dowel handle h into L 180 mm below the shaft and bolt an 8 kg kettlebell to its foot as W.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง2 ชิ้น
สกรูไม้8 ชิ้น
เหล็กกล้าแท่งดิบ1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาด3 ชิ้น
นอตล็อกไนลอน3 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
เคตเทิลเบล1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยมือ
สว่านไร้สาย
ชุดดอกสว่าน
ชุดดอกสว่านใบพาย
เลื่อยตัดเหล็ก
ประแจเลื่อน6
6
Guide bar J, arms G and links F
Guide bar J, arms G and links F
Bolt a hardwood guide bar J 444 x 40 x 36 mm across the side pieces' fronts on spacer blocks so it stands 70 mm in front of them, 530 mm above the base, and cut two 27 mm square slots through it 40 mm apart. Cut two hardwood dasher arms G G' 25 mm square and 580 mm long, drop them through the slots, and drill each 8.5 mm 20 mm below its top. Cut two links F F' 30 x 14 mm with holes 282 mm apart and bolt each from a pin c on E to a pin g on an arm, with washers and lock nuts so they turn freely.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง2 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาด6 ชิ้น
แหวนรองแบน8 ชิ้น
นอตล็อกไนลอน4 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยมือ
สิ่ว
สว่านไร้สาย
ชุดดอกสว่าน
ประแจเลื่อน7
7
Barrel D, covers, dashers and thumb screw
Barrel D, covers, dashers and thumb screw
Stand a food-grade 20-litre bucket on the base under the arms. Cut two half-discs N N' 240 mm across from 12 mm plywood, each with three 34 mm holes, and screw one under each arm's foot. Cut two half-round covers m m from 12 mm plywood to fit the bucket's top, notched for the arms. Bolt a cross brace K 444 x 40 x 30 mm across the side pieces' fronts 440 mm above the base, drill it for an M8 rod 72 mm behind the arms, and run the rod through a nut in K with a wing nut on top as the thumb screw i, down onto an oblong block l laid across both covers.
วัสดุสำหรับขั้นตอนนี้:
ถังขนาด 20 ลิตร1 ชิ้น
แผ่นไม้อัด2 ชิ้น
สกรูไม้6 ชิ้น
แผ่นไม้เนื้อแข็ง1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาด2 ชิ้น
เพลาเกลียว1 ชิ้น
น็อตหกเหลี่ยม1 ชิ้น
น็อตปีกผีเสื้อ1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยจิ๊กซอว์
ชุดโฮลซอว์
สว่านไร้สาย
ชุดดอกสว่าน
ชุดไขควง
ประแจเลื่อน8
8
The build in 3D
The build in 3D
FreeCAD model of this build, a quarter of the barrel and covers cut away: the base and frame with its braces, shaft M with lever E in front and the weighted pendulum behind, links F, the arms in guide bar J, the two half-dashers in the barrel, and the thumb screw on its block. It was checked at five pendulum angles from -12 to +12 degrees.
9
9
Churn
Churn
Lift the front cover, pour in about 10 litres of heavy cream at about 15 °C, checked with the thermometer, put the cover back and turn the thumb screw down on the block. Swing the pendulum by its handle about 12 degrees each way and time it: the half-dashers rise and fall in turn. When the butter comes, slacken the screw, unbolt the dashers, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด10 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่10
10
Troubleshooting
Troubleshooting
Pendulum churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**James O. Merrill** of Chichester, Merrimack County, New Hampshire, assignor to Wm. A. Swain, US 23,986, 10 May 1859, "Churn". He meant it to take the labour out of churning, adapted to the strength of a child, and claimed the pendulum and weight with the shaft, beam, links and the two alternate dasher arms. He gave no sizes or weight: the frame, the 8 kg weight, the 12 degree swing and every size are ours.
วัสดุ
20- 2 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 30 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 14 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 7 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 8 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 10 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
17- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
1พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้



