ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Mitre Gears: a 1:1 Bevel Pair Cut on the Milling Machine (Brown & Sharpe 1911)
Forge

สร้างโดย

Forge

27. ตุลาคม 2026NO
16
0
0
0
0

Mitre Gears: a 1:1 Bevel Pair Cut on the Milling Machine (Brown & Sharpe 1911)

Two equal bevel gears on shafts at right angles are mitre gears, and one cutter cuts both. A rotary cutter can only be right for one end of a bevel tooth, so Brown & Sharpe cut each space twice, set off centre to each side, then file the small ends round. Every figure here comes from their rules, worked out for a pair of 16 teeth, 8 pitch. Source: Brown & Sharpe, Practical Treatise on Gearing (1911), Part I ch. IX–X and Part II ch. III; set-over table p. 58. The tooth count, pitch, face width, steel and bore are ours, and so is the arithmetic. Picture: Brown & Sharpe's Fig. 24.
ขั้นสูง
2 days

คำแนะนำ

1

Work out and turn two blanks

Ours: 16 teeth, 8 pitch, so pitch diameter 2.000 in. Mitre gears have a 45° centre angle (tangent 16/16). Diameter increment = cos 45° × working depth 0.250 = 0.177 in. Apex distance 1.414 in. Angle increment: tan = sin 45° ÷ 8, giving 5° 03′; cutting and face angle 45° − 5° 03′ = 39° 57′. Turn two blanks from steel to 2.18 in outside diameter, with the angle of edge 45° and the angle of face 39° 57′, tried with a protractor against the end of the hub. Face length ⅜ in (ours; no more than a third of the 1.414 in apex distance). Bore and hub are ours.

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กกล้าละมุนแท่งเหล็กกล้าละมุน1 length for two blanks

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
มีดกลึงมีดกลึง
ไม้โปรแทรกเตอร์ไม้โปรแทรกเตอร์
ไมโครมิเตอร์ไมโครมิเตอร์
2

Choose the cutter

Back cone radius 1.414 in: twice that × 8 pitch = 22.6 teeth, so a No. 5, 8-pitch bevel gear cutter (21 to 25 teeth). One cutter does both gears. Measure its thickness Tc at the pitch line, 0.145 in (1.157 ÷ 8) from its tip.

เครื่องมือที่ต้องใช้:

ดอกกัดเฟืองดอกจอกดอกกัดเฟืองดอกจอก
เวอร์เนียร์วัดฟันเฟืองเวอร์เนียร์วัดฟันเฟือง
3

Set the head and the depth

Mount the blank on the dividing head, set to the cutting angle of 39° 57′, to index 16 spaces. Set the depth at the large end to the working depth plus clearance, 0.270 in. Clearance stays the same at the small end.

เครื่องมือที่ต้องใช้:

เครื่องกัดเครื่องกัด
หัวแบ่งหัวแบ่ง
ดอกกัดเฟืองดอกจอกดอกกัดเฟืองดอกจอก
4

Set over and cut one side of every tooth

Set-over: apex distance ÷ face = 1.414 ÷ 0.375 = 3.77, so use the 3¾ column, where a No. 5 cutter has the factor .293. Set-over = Tc ÷ 2 − .293 ÷ 8 = Tc ÷ 2 − 0.037 in. Set the work off centre by that amount to one side, taking up backlash. Run the cutter through, indexing round all 16 spaces.

เครื่องมือที่ต้องใช้:

เครื่องกัดเครื่องกัด
หัวแบ่งหัวแบ่ง
ดอกกัดเฟืองดอกจอกดอกกัดเฟืองดอกจอก
5

Set over the other way and trim to thickness

Set over by the same amount on the other side of centre and rotate the blank to line the cutter up with the space at the small end. Take a trial cut, then rotate the blank toward the cutter until the tooth is right: 0.196 in thick at the large end and 0.144 in at the small end. Check both ends with the gear tooth vernier. Right at the large end but thick at the small end means too much set-over; the other way round, too little.

เครื่องมือที่ต้องใช้:

เครื่องกัดเครื่องกัด
หัวแบ่งหัวแบ่ง
ดอกกัดเฟืองดอกจอกดอกกัดเฟืองดอกจอก
เวอร์เนียร์วัดฟันเฟืองเวอร์เนียร์วัดฟันเฟือง
6

Cut round, then make the second gear

Cut the second side of every tooth with that setting. Cut the second blank the same way with the same cutter.

เครื่องมือที่ต้องใช้:

เครื่องกัดเครื่องกัด
หัวแบ่งหัวแบ่ง
ดอกกัดเฟืองดอกจอกดอกกัดเฟืองดอกจอก
7

File the small ends

Round the teeth over at the small ends with a file, where the cutter could not. Do not file them thinner at the pitch line.

เครื่องมือที่ต้องใช้:

ตะไบเนื้อละเอียดตะไบเนื้อละเอียด

วัสดุ

1

เครื่องมือที่จำเป็น

9

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...