การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Turner's Pole Lathe with Puppets, Screw Centre and Treadle (Moxon, 1680)
Woody

สร้างโดย

Woody

14. พฤศจิกายน 2026NO
8
0
0
0
0

Turner's Pole Lathe with Puppets, Screw Centre and Treadle (Moxon, 1680)

The workshop pole lathe of Joseph Moxon's Mechanick Exercises: legs and twin cheeks bolted square, sliding puppets wedged through the bed, a fixed steel-pointed pike and an adjustable screw centre, a hinged treadle with a cross-treadle, and a fir pole pinned to the ceiling for the spring.
ขั้นสูง
Two to three days

คำแนะนำ

1

His sizes

กำลังโหลดสมุด Jupyter…
2

Read Mechanick Exercises

"The Lathe is described in Plate 12. A. This Machine is so vulgarly known..."
3

Legs and cheeks

Set up two legs about 2 ft 10 in (86 cm) high, plumb, each with a tenon on top as thick as the gap you want between the two cheeks. Lay a cheek each side of the tenons, level, and fix them: pinned, or better with an iron bolt whose square neck sits in a square hole in the near cheek, drawn up by a nut. Brace legs and cheeks to the floor and walls so nothing trembles.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้โอ๊กขาวแผ่นไม้โอ๊กขาว1 ชิ้น
สลักเกลียวหัวกลมสลักเกลียวหัวกลม1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
สิ่วเจาะเดือยสิ่วเจาะเดือย
ค้อนไม้ค้อนไม้
สว่านมือหมุนพร้อมดอกสว่านมือหมุนพร้อมดอก
4

Puppets

Make two (or two or three pairs of) square puppets, strong rather than weak and as short as your work allows: the centres must stand a little more than half the work's diameter above the cheeks. Give each a tenon at the foot that slides in the gap between the cheeks, with a mortise through it below the cheeks for a tapering wedge, driven with a mallet to clamp the puppet down.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้โอ๊กขาวแผ่นไม้โอ๊กขาว1 ชิ้น
ลิ่มไม้เนื้อแข็งลิ่มไม้เนื้อแข็ง1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
สิ่วเจาะเดือยสิ่วเจาะเดือย
ค้อนไม้ค้อนไม้
5

Pike and screw centre

Near the top of one puppet fix a strong iron pike with a tempered steel point. Through the other fit an iron screw in a nut in the puppet, also with a steel point, both points in one straight line facing each other. Put an iron handle 7-8 in long with a knob at each end through the screw head. Cut the puppets to square shoulders just below the pikes to carry the rest.

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กดัดแท่งเหล็กดัด1 ชิ้น
เหล็กเครื่องมือสี่เหลี่ยมจัตุรัสเหล็กเครื่องมือสี่เหลี่ยมจัตุรัส1 ชิ้น

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
ถังชุบน้ำถังชุบน้ำ
6

Rest and oil horn

Make the rest a square piece 1-1.5 in thick, 2-2.5 in broad, a little longer than the gap between the puppets. Hang a horn tip down on the outside of the right-hand puppet near the top, filled with oil, with a wooden cover and button carrying an iron wire that reaches nearly to the bottom, to oil the centre holes.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้โอ๊กขาวแผ่นไม้โอ๊กขาว1 ชิ้น
เขาวัวเขาวัว1 ชิ้น
ลวดเหล็กดัดลวดเหล็กดัด1 ชิ้น
น้ำมันเครื่องจักรน้ำมันเครื่องจักร1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
สว่านมือหมุนพร้อมดอกสว่านมือหมุนพร้อมดอก
7

Treadle and cross-treadle

Make a treadle about 2.5 in broad, 1 in thick and 3 ft (up to 4 ft) long. Nail its back end to the floor with a piece of leather, 1-1.5 ft behind the lathe and midway between the legs, so the front reaches 1.5-2 ft past the front of the lathe. Cut a square notch 1.5 in wide and 2 in long in the far end for winding the string. Fix an iron pin about 0.5 in thick, standing 1.5-2 in up, in the middle; under the cheeks fix a cross-treadle with a row of holes 2-3 in apart to take the pin.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้โอ๊กขาวแผ่นไม้โอ๊กขาว1 ชิ้น
สายหนังสายหนัง1 ชิ้น
ตะปูเหล็กตะปูเหล็ก1 ชิ้น
แท่งเหล็กดัดแท่งเหล็กดัด1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
ค้อนค้อน
สว่านมือหมุนพร้อมดอกสว่านมือหมุนพร้อมดอก
8

Pole and string

Use a fir pole, thick or thin to suit the work; if it is too stiff, thin its upper and under sides with a draw-knife. Pin the thick end to a ceiling timber with one nail so it pivots. About a foot away nail two cheeks to the joists with a batten across their foot to carry the pole. Run the string from the pole's thin end, round the work, to the treadle.

วัสดุสำหรับขั้นตอนนี้:

เสาไม้เสาไม้1 ชิ้น
เชือกเส้นเล็กเชือกเส้นเล็ก1 ชิ้น
ตะปูเหล็กตะปูเหล็ก1 ชิ้น
แผ่นไม้โอ๊กขาวแผ่นไม้โอ๊กขาว1 ชิ้น

เครื่องมือที่ต้องใช้:

มีดสองมือมีดสองมือ
ค้อนค้อน
9

Troubleshooting

Pole lathe troubleshooting.

Flow

Loading...
10

History and honest limits

From Joseph Moxon, **Mechanick Exercises**, Numb. X, Turning (1680), pp. 176-185 and Plate 12 (checked on the archive.org scan mechanickexercis00moxo). He gives no sizes for cheeks, puppets or pole; metric and the wood choices are ours.

วัสดุ

12

เครื่องมือที่จำเป็น

10

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...