ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Oil Storage Tank: a Riveted Steel Tank with Globe Roof (Bell, 1923)
An above-ground oil tank of riveted 'tank steel': a flat bottom, rings of plate lapped and riveted, angle irons at top and bottom, and a self-supporting globe roof. Every seam is caulked oil-tight and the tank is water-tested before painting.
Variable: capacity. Bell's Fig. 158 is 1,000 barrels: 20 ft inside diameter, about 20 ft 3 in high, four rings of 1/4 in plate, sixteen 3/16 in roof plates rising 3 ft. Standard tanks run from 500 to 80,000 barrels (120 ft x 40 ft).
Source: H. S. Bell, American Petroleum Refining (1923), pp. 286-306. Picture: Fig. 158 of the book.
ผู้เชี่ยวชาญ
Unknown
คำแนะนำ
1
1
Choose the size and plates
Choose the size and plates
Pick the capacity from the standard sizes (1,000 barrels: 20 ft diameter, 20 ft high). Take plate thickness from Bell's chart for the head and diameter, with a factor of safety of at least 2 1/2 for refinery tanks. Use at least 1/4 in for the shell; bottom 1/4 in on larger tanks, 3/16 in on smaller. Rings are 6 ft (72 in plates); about 7 ft is the limit.
เครื่องมือที่ต้องใช้:
ขนาดที่ไม่ทราบ2
2
Prepare the ground
Prepare the ground
Level the ground in a circle 10 ft wider than the tank and remove all vegetable growth. Avoid a mix of cut and fill. In old yards filled with cinders, dig them out at least 8 in deep and replace with fine gravel, loam or sand. On poor soil, use piles.
วัสดุสำหรับขั้นตอนนี้:
กรวด1 as neededเครื่องมือที่ต้องใช้:
ขนาดที่ไม่ทราบ3
3
Punch and scarf the plates
Punch and scarf the plates
Punch the rivet holes. For 1/4 in plate with 5/8 in rivets, a single lap seam has holes 2 1/4 in apart and 1 1/8 in from the edge; keep the clear space between holes no more than 6 or 7 times the plate thickness, or the caulked edge springs. Scarf the corner of the middle plate where three plates meet: cold up to 1/4 in, hot above, drawn to an edge no thicker than 1/16 in.
เครื่องมือที่ต้องใช้:
เครื่องปั๊มเจาะ
ค้อนปอนด์4
4
Build the bottom on horses
Build the bottom on horses
Lay, rivet and caulk the bottom on trestles or horses about 30 in high. Rivet the bottom angle iron (Fig. 158: 3 x 3 x 5/16 in) with a 1/4 in bent-plate shoe behind each angle splice; caulk the shell leg past the shoe at least 12 in, or better bevel and caulk the angle all round. Assemble and drive the first ring while the bottom is still up. Test the bottom under 6 to 8 in of water. Coat its underside with ship-bottom or heavy asphalt paint.
วัสดุสำหรับขั้นตอนนี้:
แผ่นเหล็กกล้าละมุน1 bottom, first ring
เหล็กฉากเหล็กกล้าละมุน1 bottom angle
หมุดย้ำเหล็กกล้า1 ชิ้น
วัสดุที่ไม่ทราบ1 asphalt paintเครื่องมือที่ต้องใช้:
ค้อนย้ำหมุด
เหล็กขยายรู
น้ำ
แปรงทาสีหน้ากว้าง5
5
Lower it and raise the shell
Lower it and raise the shell
Raise the tank on jacks round the edge, clear out the horses and debris, and lower the bottom to grade. Rivet and caulk the remaining rings from scaffolds: floating scaffolds where water is at hand (water is pumped in as each ring is caulked tight, testing as you go), or brackets bolted through punched holes, later plugged with hot rivets. Where three plates meet, bolt them, heat cherry red with an oil-burning torch and lay the joint up with sledges before riveting. Fit the top angle (2 1/2 x 2 1/2 x 5/16 in) and a flanged steel manhole in the bottom ring.
วัสดุสำหรับขั้นตอนนี้:
แผ่นเหล็กกล้าละมุน1 rings
เหล็กฉากเหล็กกล้าละมุน1 top angle
หมุดย้ำเหล็กกล้า1 ชิ้นเครื่องมือที่ต้องใช้:
แม่แรงเกลียว
ค้อนย้ำหมุด
เหล็กขยายรู
คบเพลิง
ค้อนปอนด์
น้ำ6
6
Fit the globe roof
Fit the globe roof
For tanks up to 54 ft across, rivet on a self-supporting globe roof of segmental 3/16 in plates (Fig. 158: sixteen plates, 1/4 in centre plate, 3 ft rise); cold riveting is fine here. Make it gas-tight, with one vent at the apex covered by brass or monel wire cloth of at least 50 mesh.
วัสดุสำหรับขั้นตอนนี้:
แผ่นเหล็กกล้าละมุน1 roof
หมุดย้ำเหล็กกล้า1 ชิ้นเครื่องมือที่ต้องใช้:
ค้อนย้ำหมุด7
7
Test and paint
Test and paint
Fill the tank with water to test it before painting; it shows the important leaks, though not always tightness for light oils. Wire-brush off mill scale and rust. Give shell and roof three coats: one of red lead ground in boiled linseed oil, then two of good grey graphite paint.
วัสดุสำหรับขั้นตอนนี้:
ตะกั่วแดง1 first coat
น้ำมันลินสีดต้ม1 ชิ้น
วัสดุที่ไม่ทราบ2 grey graphite paintเครื่องมือที่ต้องใช้:
น้ำ
ชุดแปรงลวด
แปรงทาสีหน้ากว้างวัสดุ
7- 1 as neededตัวยึดตำแหน่ง
- 1 roofตัวยึดตำแหน่ง
- 1 top angleตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 grey graphite paintตัวยึดตำแหน่ง
- 1 first coatตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
วัสดุจากพิมพ์เขียวที่เชื่อมต่อ

การระบุ 10%
Mild Steel Plate and Sheet Hammered from a Billet
โดย Forge
ยุคใหม่
42
0
0
0
5
0

การระบุ 10%
Hot-Rolled Steel Angles and Channels
โดย Forge
งานโลหะ
28
0
0
0
2
0

การระบุ 10%
Steel Rivets Forged in a Nail Header
โดย Forge
ช่างตีเหล็ก
32
0
0
0
1
0

อันตราย
การระบุ 10%
Making Red Lead (Minium) — The Pigment That Named the Art of Miniature Painting
โดย Charlie
ศิลปะ
118
0
0
0
2
0
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้
