ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Oven Thermometer: Door-Mounted Dial with a Curved Bimetal Strip (Whittier, US 1,498,413, 1924)
A dial thermometer that fits in an oven door or wall. Behind an enamelled dial plate, a curved bimetal strip runs from a fixed stud to a little arm on a spindle; as the oven heats, the strip bends, turns the spindle and swings the pointer across the scale on the front. Everything is mounted on the dial plate as one unit and dropped into a shallow stamped case with a glass cap.
Result: a compact oven thermometer, easy to calibrate and adjust.
Source: H. R. Whittier, US 1,498,413 (1924). Unknown: metals, sizes and the scale unit. Picture: the patent drawing.
ระดับกลาง
Unknown
คำแนะนำ
1
1
Make the dial unit
Make the dial unit
Cut a metal disk for the dial plate, enamel its front and mark the scale (the patent's drawing reads 200 to 500). Thread a sleeve through the plate near one edge and pass a spindle loosely through it, with a pointer fixed on its front end and a short arm on its back end. Set a stud through the plate: in front it stops the pointer, behind it anchors one end of a curved bimetal strip whose other end is pinned to the arm. Not given: metals, sizes, the scale unit.
วัสดุสำหรับขั้นตอนนี้:
โลหะที่ไม่ทราบ1 dial plate, sleeve, spindle, pointer, arm, stud
วัสดุที่ไม่ทราบ1 enamel and scale
แผ่นโลหะคู่1 curved stripเครื่องมือที่ต้องใช้:
ชุดต๊าปและดายทำเกลียว
คีมปากกลม
ขนาดที่ไม่ทราบ2
2
Make the case
Make the case
Stamp a shallow case from thin sheet metal, closed at the back, with perforated ears for fixing it in the oven door or wall, and press lugs in from its wall for the dial plate to sit on. Make a cap with a glass to close the open front. Ours: steel sheet and a watch glass.
วัสดุสำหรับขั้นตอนนี้:
แผ่นเหล็กกล้าละมุน1 case and cap
กระจกนาฬิกา1 windowเครื่องมือที่ต้องใช้:
กรรไกรตัดแผ่นโลหะ
ขนาดที่ไม่ทราบ3
3
Assemble, calibrate and fit
Assemble, calibrate and fit
Calibrate the strip and set the pointer while the unit is out of the case, then drop the dial unit onto the lugs and fit the cap, which holds the plate in place. Fasten the case through its ears in the oven door or wall. As the oven heats, the strip bends and the pointer swings across the scale. Not given: how it is calibrated.
เครื่องมือที่ต้องใช้:
เตาอบ
คีมปากกลมวัสดุ
5- 1 dial plate, sleeve, spindle, pointer, arm, studตัวยึดตำแหน่ง
- 1 enamel and scaleตัวยึดตำแหน่ง
- 1 curved stripตัวยึดตำแหน่ง
- 1 case and capตัวยึดตำแหน่ง
- 1 windowตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

