ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Oxyhydrogen Blowpipe: Brass Tube-in-Tube, the Gases Meeting at the Nozzle (Work, 1892)
Forge

สร้างโดย

Forge

9. พฤศจิกายน 2026NO
10
0
0
0
0

Oxyhydrogen Blowpipe: Brass Tube-in-Tube, the Gases Meeting at the Nozzle (Work, 1892)

A blowpipe that burns hydrogen in a jet of oxygen for a very hot brazing and melting flame. H. B. Stocks (Work, 1892) builds it like his cheap gas blowpipe: a fine brass tube for the oxygen, centred inside an outer brass tube (no more than 1/4 in. bore) that carries the hydrogen, joined by a three-way tube. The two gases must not mix until they reach the nozzle; each comes from its own reservoir through its own tap. Source: H. B. Stocks, "How to Prepare Cheap Blowpipes", Work, 2 July 1892, p. 250, with his reply "Oxyhydrogen Blowpipe", Work, 3 December 1892, p. 605 (Fig. 3).
ระดับกลาง
Unknown

คำแนะนำ

1

Read Stocks

"The oxyhydrogen blowpipe for brazing ... is practically the same as the blowpipe shown at p. 250 ..., but the brass pipe should not be more than 1/4 in. internal diameter; the inner tube for oxygen about 1/12 in. internal diameter, and should reach to the mouth of the outer tube. It can then be filed down, if required."
2

Cut the tubes

Cut the brass tubes: the outer (hydrogen) tube, not more than 1/4 in. bore, threaded at one end; a curved side tube for the hydrogen supply, threaded at one end; a short straight tube for the oxygen supply, threaded at one end; and the inner oxygen tube, about 1/12 in. bore. For his gas blowpipe Stocks used 4 in., 5 1/2 in. (curved), 3 1/2 in. and 5 1/2 in.; the lengths for the brazing pipe are not given and he says the sizes may be changed. How the tube is curved is not given.

วัสดุสำหรับขั้นตอนนี้:

ท่อทองเหลืองท่อทองเหลือง4 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
วิธีขึ้นรูปที่ไม่ทราบวิธีขึ้นรูปที่ไม่ทราบ
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
3

Centre the oxygen tube

Cut a small strip of thin sheet brass (Stocks: full 3/4 in. by 1/2 in.), turn it into a ring and solder it on one end of the inner tube. File the ring down until it pushes into the threaded end of the short oxygen tube, and solder it inside.

วัสดุสำหรับขั้นตอนนี้:

แผ่นทองเหลืองแผ่นทองเหลือง1 small strip
ตะกั่วบัดกรีดีบุก-ตะกั่วตะกั่วบัดกรีดีบุก-ตะกั่ว1 ชิ้น

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
หัวแร้งบัดกรีหัวแร้งบัดกรี
ฟลักซ์ฟลักซ์
4

Assemble

Screw the oxygen tube into one end of the three-way tube, screw the outer tube on the other end and see that the inner tube is exactly in its centre. Screw the curved hydrogen tube into the side branch. Fit a tap on each supply (Fig. 3; type not given).

วัสดุสำหรับขั้นตอนนี้:

ข้อต่อท่อเกลียวข้อต่อท่อเกลียว1 three-way tube
วาล์วที่ไม่ทราบวาล์วที่ไม่ทราบ2 one per gas
5

Set the nozzle

The inner oxygen tube should reach to the mouth of the outer tube. Light it with hydrogen in the outer tube and oxygen in the inner, each from its own reservoir; if the flame shows a white patch, the inner tube is off centre or too long: file it down a little until correct. Never let the gases mix before the nozzle.

เครื่องมือที่ต้องใช้:

ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
ไฮโดรเจนไฮโดรเจน
ออกซิเจนออกซิเจน

วัสดุ

5

เครื่องมือที่จำเป็น

10

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...