การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Perforated Screen Plate: Clear- or Buhr-Punched Steel Plate (Richards, Ore Dressing, 1903)
Forge

สร้างโดย

Forge

4. พฤศจิกายน 2026NO
8
0
0
0
0

Perforated Screen Plate: Clear- or Buhr-Punched Steel Plate (Richards, Ore Dressing, 1903)

The punched steel screens of ore mills: round holes or slots punched through steel plate, either 'clear punched' with a sharp square-edged tool that cuts out a wad, or 'buhr punched' with a thicker tool that tears the metal over a socket in the die. Clear punching suits holes of 0.03 inch and up; buhr punching suits fine holes of 0.02 inch and less, because a thicker plate can be used. Holes in rows at 60° give 1.154 times the open area of rows at 90°. Unknown: the plate thickness and hole spacing for a given screen. Source: R. H. Richards, Ore Dressing vol. I (1903), pp. 167-168. Picture: p. 167 with Figs. 117 and 118.
ระดับกลาง
Unknown

คำแนะนำ

1

Choose the holes

For coarse work use round holes of 0.04 inch (1 mm) and up; for medium work about 0.03 inch (0.75 mm), clear punched. For fine work, 0.02 inch (0.5 mm) and less, buhr punch, so a thicker plate can be used. The smallest practical clear-punched hole is about 0.014 inch (0.35 mm) wide: a hole much narrower than the plate is thick breaks the punch (the extreme Richards found was a slot 54 per cent of the thickness).

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กแผ่นเหล็ก1 steel plate
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องปั๊มเจาะเครื่องปั๊มเจาะ
2

Lay out the holes

Set round holes in rows at 60° or 90°; with the same hole and spacing, 60° rows give 1.154 times the open area. Punch slots vertical, diagonal or horizontal, in line or staggered; staggering spreads the punching strain.

เครื่องมือที่ต้องใช้:

เครื่องปั๊มเจาะเครื่องปั๊มเจาะ
3

Punch the plate

Clear punching: a tool with a square, sharp edge cuts out a wad exactly the size and shape of the hole. Buhr punching: a thicker tool presses the plate, lying on a socket in the die, just deep enough to tear the metal apart.

เครื่องมือที่ต้องใช้:

เครื่องปั๊มเจาะเครื่องปั๊มเจาะ

วัสดุ

2

เครื่องมือที่จำเป็น

1

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...