ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Pressure Reactor: the Cast-Iron Autoclave with Bolted Cover (Thorpe, 1912)
The chemical works' autoclave, built on Papin's digester: a closed cast-iron vessel with a flanged cover bolted down on a lead washer, a pressure gauge, a safety valve and a thermometer tube. It heats liquids above their boiling points, often at 20 to 30 atmospheres, in a bath of hot oil or molten lead.
Variable: the material (cast iron, steel, copper, sheet iron) and lining (enamel, tin, lead, copper or zinc).
Source: Thorpe, Dictionary of Applied Chemistry, vol. I (1912), pp. 343-344. Unknown: sizes, wall thickness. Picture: Fig. 3 of the book.
ผู้เชี่ยวชาญ
Unknown
คำแนะนำ
1
1
Cast the body and cover
Cast the body and cover
Make the vessel of cast iron (or steel; occasionally copper, sheet iron or sheet steel), with a flange for the cover (Figs. 1-3). Cast-iron vessels are sometimes strapped with steel rings for safety. Not given: sizes and wall thickness.
วัสดุสำหรับขั้นตอนนี้:
ชิ้นงานเหล็กหล่อ2 body, cover
เหล็กแบนกล้าละมุน1 rings, optionalเครื่องมือที่ต้องใช้:
ขนาดที่ไม่ทราบ2
2
Fit gauge, valve and thermometer tube
Fit gauge, valve and thermometer tube
Fit a pressure gauge, a safety valve and tubes for thermometers. If the charge would attack the iron, enamel the inside or line it with sheet tin, lead, copper or zinc soldered tight to the wall.
วัสดุสำหรับขั้นตอนนี้:
เกจวัดความดัน1 ชิ้น
วาล์วที่ไม่ทราบ1 safety valve
ท่อเหล็ก1 thermometer tubeเครื่องมือที่ต้องใช้:
ชุดประแจปากตาย3
3
Close the cover
Close the cover
Close it with a screwed or flanged cover bearing on a lead washer, bolted down evenly.
วัสดุสำหรับขั้นตอนนี้:
แผ่นตะกั่ว1 washer
สลักเกลียวหัวหกเหลี่ยม - เกรด 8.81 flange bolts, number not givenเครื่องมือที่ต้องใช้:
ชุดประแจปากตาย4
4
Pressure-test and heat
Pressure-test and heat
Because it must hold 20 to 30 atmospheres, test it with hydraulic (water) pressure before use. In service, heat it by circulating hot oil or by standing it in a bath of molten lead.
เครื่องมือที่ต้องใช้:
ปั๊มทดสอบแรงดันแบบมือโยก
น้ำ
อ่างตะกั่วหลอมเหลววัสดุ
7- 2 body, coverตัวยึดตำแหน่ง
- 1 rings, optionalตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 safety valveตัวยึดตำแหน่ง
- 1 thermometer tubeตัวยึดตำแหน่ง
- 1 washerตัวยึดตำแหน่ง
- 1 flange bolts, number not givenตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
5- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้
