การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Protractor: Plain Circular Brass Protractor with a Centre Bar (Stanley, 1878)
The draughtsman's circular protractor: a flat brass ring divided all round into degrees and half-degrees, its outer edge bevelled thin so a needle point can feel the divisions, with a bar across the middle whose edge runs exactly through the centre from 0° to 180°. Lay the bar on a line, prick off the angle and draw through the point and the centre.
Result: a protractor for setting off and measuring angles on a drawing.
Source: W. F. Stanley, A Descriptive Treatise on Mathematical Drawing Instruments (1878), pp. 227-228. Unknown: sizes and how the circle is divided. Picture: the book's figure.
ระดับกลาง
Unknown
คำแนะนำ
1
1
Make the ring and bar
Make the ring and bar
Cut a flat ring of brass (electrum also serves) with a bar across the inner space. Make one side of the bar a true straight line through the centre of the ring, and mark the centre with a short line in the middle of the bar; a small semicircle may be cut out of the bar's edge there to make it easier to set over a point. Bevel the outer edge down very thin. Not given: sizes. Ours: brass sheet.
วัสดุสำหรับขั้นตอนนี้:
แผ่นทองเหลือง1 ring and barเครื่องมือที่ต้องใช้:
กรรไกรตัดแผ่นโลหะ
เครื่องกลึงโลหะ
ขนาดที่ไม่ทราบ2
2
Divide it
Divide it
Divide the circumference into degrees, subdivided into half-degrees, so that the bar's edge, carried on, reads 0° and 180°, and number the degrees. Not given: how the circle is divided.
เครื่องมือที่ต้องใช้:
ขนาดที่ไม่ทราบ3
3
Use it
Use it
To set off an angle from a point on a line, lay the bar so it half covers the line, the line reading 0 to 180, with the point in the centre. Prick off the number of degrees at the bevelled edge with a needle point, lift the protractor away, and draw a line through the mark and the point.
เครื่องมือที่ต้องใช้:
ขนาดที่ไม่ทราบวัสดุ
1- 1 ring and barตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
3- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้
