การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Laminate Bevel Trimmer: Two Pads at Right Angles Hold a Small Router at 45 Degrees on a Corner (Roche, 1971)
Forge

สร้างโดย

Forge

13. พฤศจิกายน 2026NO
6
0
0
0
0

Laminate Bevel Trimmer: Two Pads at Right Angles Hold a Small Router at 45 Degrees on a Corner (Roche, 1971)

Edward Noland Roche of Cockeysville, Maryland, received US 3,628,579, dated 21 December 1971, for a small router that bevels plastic laminate in place. Laminate is usually trimmed after it is glued down, and a mitred corner meant mitring the wood underneath too. Roche's tool rides on the corner of the already-built carcass. A fixed pad with a 45 degree face sits on the top surface, a tilting pad sits on the side face, and the cutter between them bevels the laminate's edge inwards, exactly to the edge beneath it. The guide base swings slightly on a pivot to line the pad up with the cutter. We print the motor unit, base and pads in PETG round a small DC motor. The 45 degrees is his; the other sizes are ours.
ขั้นสูง
About 2 days

คำแนะนำ

1

Why the substrate needs no mitre

กำลังโหลดสมุด Jupyter…
2

Read US 3,628,579

"This pad 40 has a raised guide face 42 that slopes at a 45 degree plane which extended, coincides with the far edge of the cutting tool." "An inwardly sloping bevel 58 which exactly conforms with the edge of the substrate 50 results."
3

Print the motor unit

The motor unit 12: a tube for a 42 mm motor with the square faceplate 16 at its end, an 18 mm hole and two M4 holes for the motor, a hole to tap M4 for the pivot stud 26 and one to tap M5 for the adjusting screw 22, and two handle bosses. Print it faceplate down. PETG, 0.2 mm layers, 40 % infill, 5 walls.
ไฟล์แบบSTLCC0 - Free
4

Print the guide base

The base 18: a flat plate with the clearance hole 24, the stud hole, the curved slot 28, the fixed pad 40 with its 45 degree face 42, and the two ears 30. Print it plate down. PETG, 0.2 mm layers, 40 % infill, 5 walls.
ไฟล์แบบSTLCC0 - Free
5

Print the adjustable pad

The pad 32 with its two cheeks 36, each with a hole for the pivot screw 34 and an arc slot for the locking screw 38. Print it plate down. PETG, 0.2 mm layers, 40 % infill, 5 walls.
ไฟล์แบบSTLCC0 - Free
6

Motor unit

Tap the faceplate's two holes M4 and M5. Fit the collet adapter on the motor, stand the motor in the tube with its face on the faceplate and the collet through the hole, screw it in with two M4 screws, and wire it through a toggle switch to the DC supply. Turn two hardwood knobs 56 and bolt them to the handle bosses.

วัสดุสำหรับขั้นตอนนี้:

เส้นใย PETGเส้นใย PETG1 ชิ้น
มอเตอร์ไฟฟ้ามอเตอร์ไฟฟ้า1 ชิ้น
อะแดปเตอร์คอลเล็ตสำหรับแกนมอเตอร์อะแดปเตอร์คอลเล็ตสำหรับแกนมอเตอร์1 ชิ้น
สกรูหัวจมหกเหลี่ยมสกรูหัวจมหกเหลี่ยม2 ชิ้น
สวิตช์โยกสวิตช์โยก1 ชิ้น
สายฮุกอัปสายฮุกอัป1 ชิ้น
ท่อหดความร้อนท่อหดความร้อน1 ชิ้น
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด2 ชิ้น
น็อตหกเหลี่ยมน็อตหกเหลี่ยม2 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
ด้ามจับต๊าปเกลียวด้ามจับต๊าปเกลียว
แหล่งจ่ายไฟกระแสตรงแหล่งจ่ายไฟกระแสตรง
หัวแร้งไฟฟ้าหัวแร้งไฟฟ้า
ชุดประแจหกเหลี่ยมชุดประแจหกเหลี่ยม
เครื่องกลึงไม้เครื่องกลึงไม้
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
7

Guide base, pads and setting

Fit a 1/4 inch straight bit in the collet. Lay the base on the faceplate, the cutter through its hole; screw an M4 screw through the corner hole into the faceplate as the pivot stud 26, and an M5 screw with a washer through the curved slot as the adjusting screw 22. Hold a straightedge on the fixed pad's sloping face, reaching past the cutter, and swing the base on its stud until the straightedge just touches the cutter's far edge; tighten the adjusting screw. Hang the adjustable pad on the ears with two M4 pivot screws 34 and two M4 locking screws 38 through its arc slots; set it square to the fixed pad's face for 90 degree corners and lock it.

วัสดุสำหรับขั้นตอนนี้:

สกรูหัวจมหกเหลี่ยมสกรูหัวจมหกเหลี่ยม6 ชิ้น
แหวนรองแบนแหวนรองแบน3 ชิ้น

เครื่องมือที่ต้องใช้:

ชุดดอกเราเตอร์ชุดดอกเราเตอร์
ชุดประแจหกเหลี่ยมชุดประแจหกเหลี่ยม
ฉากรวมอเนกประสงค์ฉากรวมอเนกประสงค์
ไม้โปรแทรกเตอร์ไม้โปรแทรกเตอร์
8

Bevel a laminate edge

Clamp a sheet temporarily to one face of the built carcass with its edge standing proud past the corner. Hold the tool by its knobs at 45 degrees, fixed pad on the top surface and adjustable pad on the side, switch on and run it along the edge until both pads bear on the work and the cutting stops: the laminate's edge is bevelled exactly to the corner. Take the sheet off, keep it for gluing, and do the next face.

เครื่องมือที่ต้องใช้:

แคลมป์แบบบาร์แคลมป์แบบบาร์
แว่นนิรภัยแว่นนิรภัย
9

Troubleshooting

Laminate trimmer troubleshooting.

Flow

Loading...
10

History and honest limits

**Edward Noland Roche** of Cockeysville, Maryland, US 3,628,579, dated 21 December 1971, filed 18 November 1969. He claimed a laminate chamfering machine with a faceplate and cylindrical cutter, a guide base pivoted at one corner and locked through "a curved slot formed therein to the radius from said pivot means", pads on the base's two halves, and "a guide pad having a raised guide face sloping at a predetermined plane which extended coincides with the far edge of said cutting tool". He gives the 45 degree slope and no sizes; ours are printed PETG parts round a small DC motor, and we set the pad to the cutter with a straightedge rather than by a figure.

วัสดุ

11

เครื่องมือที่จำเป็น

14

ไฟล์ออกแบบ

3

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...