การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Jack-o'-Lantern Light: a Dry Cell in a Tin Clip and a Hinged Bulb Holder Instead of a Candle (Root, 1953)
Forge

สร้างโดย

Forge

13. พฤศจิกายน 2026NO
10
0
0
0
0

Jack-o'-Lantern Light: a Dry Cell in a Tin Clip and a Hinged Bulb Holder Instead of a Candle (Root, 1953)

Howard S. Root of Spokane received US 2,631,224, dated 10 March 1953, for a safe light for jack-o'-lanterns: "The most common device is an ordinary candle. That, however, is very dangerous." A springy tin clip holds a dry cell; a bulb screwed into a hinged tin support rests on the top of the cell, and the clip itself carries the current back from the bottom. A wire handle through the lid lifts the bulb to switch it off. We bend it from tinplate and fit it in a carved pumpkin. All sizes are ours.
เริ่มต้น
About 2 hours

คำแนะนำ

1

Bracket blank

กำลังโหลดสมุด Jupyter…
2

Read US 2,631,224

"I provide an operating means for the light bulb support 18 of such a nature that the child can turn the light on and off at will, yet if the entire toy is carried by the operating handle, no harm is done to the device."
3

Bend the cell clip

Cut the tinplate strip from the notebook. Bend it into a U round the cell, his container 10: the bottom is the cross bar 10c, the sides are legs 10a and 10b. Curve the legs a little across their width so the cell cannot slide out sideways, and snip and press in a small tongue on each leg (his 15) to grip it. Snip two pointed fingers at the bottom (his 13).

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กชุบดีบุกแผ่นเหล็กชุบดีบุก1 ชิ้น

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
คีมปากแบนคีมปากแบน
4

Make the bulb support

Cut a tin plate a little longer than the cell is wide, his support 18. Punch a hole in the middle just big enough for the bulb's screw base to screw into (his threaded aperture 19; ours). Bend two small ears at the top of leg 10a (his 21) and roll the support's end round a wire pin (22) between them, so it hinges.

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กชุบดีบุกแผ่นเหล็กชุบดีบุก1 ชิ้น
ลวดเหล็กสปริงลวดเหล็กสปริง1 ชิ้น

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
เหล็กตอกนำศูนย์เหล็กตอกนำศูนย์
คีมปากกลมคีมปากกลม
คีมปากแบนคีมปากแบน
5

Fit the spring and handle

Wind a few turns of spring wire on the hinge pin, one end hooked over the top of leg 10a and the other over the support, so it presses the support down (his spring 25). Bend a wire handle (his 20) long enough to come out of the top opening; pivot its lower end in a turned-over tab on leg 10b (26) and bend a short arm (27) under the free end of the support, so raising the handle lifts the bulb.

วัสดุสำหรับขั้นตอนนี้:

ลวดเหล็กสปริงลวดเหล็กสปริง1 ชิ้น

เครื่องมือที่ต้องใช้:

คีมปากกลมคีมปากกลม
คีมปากแบนคีมปากแบน
คีมตัดลวดปากเฉียงคีมตัดลวดปากเฉียง
6

Put in the cell and bulb

Seat the cell with its centre terminal down on the cross bar, put a tin band (his 16) round the legs if they are loose, and screw the bulb into the support. Let the support down: the bulb's end terminal should touch the top of the cell and light, the current returning through the support, the hinge and the clip.

วัสดุสำหรับขั้นตอนนี้:

ถ่านไฟฉาย (เซลล์แห้ง)ถ่านไฟฉาย (เซลล์แห้ง)1 ชิ้น
หลอดไฟฉายหลอดไฟฉาย1 ชิ้น
แผ่นเหล็กชุบดีบุกแผ่นเหล็กชุบดีบุก1 ชิ้น

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
คีมปากแบนคีมปากแบน
7

Fit it in the pumpkin

Carve the pumpkin's face and cut the top opening (ours; his toys are hollow figures). Push the clip's fingers through the bottom of the pumpkin, put a washer over them outside, and bend them over it (his washer 8), so the light stands in the middle. Pass the handle up through the top opening.

วัสดุสำหรับขั้นตอนนี้:

ฟักทองฟักทอง1 ชิ้น
แหวนรองแบนแหวนรองแบน1 ชิ้น

เครื่องมือที่ต้องใช้:

มีดคัตเตอร์งานประดิษฐ์มีดคัตเตอร์งานประดิษฐ์
คีมปากแบนคีมปากแบน
8

Use it

Lower the handle and the bulb lights; raise it and the light goes off. To change the cell, lift the support and take the cell out.
9

Troubleshooting

Jack-o'-lantern light troubleshooting.

Flow

Loading...
10

History and honest limits

**Howard S. Root** of Spokane, Washington, US 2,631,224, dated 10 March 1953, filed 21 December 1948. He claimed "an illuminated figure toy comprising a hollow body having an opening in the top thereof", a conductive container for a dry cell, a hinged conductive bulb support, and spring means pressing the bulb's end terminal against the cell. He also shows other hinges, a magnet latch and a side handle (Figs. 6-13), not built here. He gives no sizes or materials: the tinplate, all sizes, the pumpkin and the cell and bulb are ours.

วัสดุ

6

เครื่องมือที่จำเป็น

6

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...