การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Rubber Type Set: Moulded from Printer's Type in a Plaster Matrix and Cut Apart (Sloane, 1891)
Emma

สร้างโดย

Emma

8. พฤศจิกายน 2026SE
11
0
0
0
0

Rubber Type Set: Moulded from Printer's Type in a Plaster Matrix and Cut Apart (Sloane, 1891)

Single rubber letters and figures for stamping, copied from printer's type. T. O'Conor Sloane (1891) sets up the type, takes a plaster matrix of it, presses uncured rubber sheet onto the matrix inside a shallow frame with a plunger, cures it at 284 °F (140 °C) for half an hour, and cuts the block apart into single type with a wet knife. High quads and spaces between the letters keep the face of the block level, so the letters stand up from a smooth surface. Source: T. O'C. Sloane, Rubber Hand Stamps and the Manipulation of Rubber (1891), Ch. VI pp. 73-76, matrix Ch. V pp. 53-55. Picture: his type mould, p. 74.
ระดับกลาง
Unknown

คำแนะนำ

1

Read Sloane

"The type which are to be copied are set up on a level base or imposing stone, and quads or spaces are put between them. ... After oiling the faces a matrix is produced exactly as described for stamps. Before it has set quite hard the plaster or cement is cut off so that it will just fit within a little 'flask' or frame."
2

Set up the type

Set up the letters and figures to be copied on a level stone or piece of marble, with high quads and spaces between them (or push the spaces up level with the shoulders of the type). Lock them in a frame of two wooden strips screwed together at their ends, and lay distance pieces each side reaching about 1/8 in. above the type faces.

เครื่องมือที่ต้องใช้:

ตัวพิมพ์เรียงแยกชิ้น (ชุด)ตัวพิมพ์เรียงแยกชิ้น (ชุด)
ก้อนหินอ่อนก้อนหินอ่อน
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง
สกรูไม้สกรูไม้
3

Make the plaster matrix

Dissolve dextrine in water until the solution is as thick as thin syrup and mix dental (or common) plaster of Paris with it to a rather stiff putty. Spread it 3/16 to 1/4 in. deep on a flat, true iron plate a little larger than the type, smoothing it with a knife. Oil the type faces with olive oil and wipe the excess out of the hollows with blotting paper. Turn the plate over and press it steadily down onto the type until it strikes the distance pieces; after about ten minutes lift it off.

เครื่องมือที่ต้องใช้:

ปูนปลาสเตอร์ปูนปลาสเตอร์
เดกซ์ทรินเดกซ์ทริน
น้ำน้ำ
แผ่นเหล็กแผ่นเหล็ก
มีดครัวมีดครัว
น้ำมันมะกอกน้ำมันมะกอก
กระดาษซับหมึกกระดาษซับหมึก
4

Make the flask and plunger

Before the plaster has set quite hard, cut it so that it just fits inside a small frame (the flask) of wood, about 1/2 to 5/8 in. deep and large enough to take the whole face of the matrix. Cut a block of wood to fit closely inside the frame like a plunger, with shoulders or cross pieces that stop it at the right depth. Fix the matrix plate to the bottom of the flask with screws. The flask's other sizes are not given (unknown).

เครื่องมือที่ต้องใช้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง
ท่อนไม้เนื้อแข็งท่อนไม้เนื้อแข็ง
มีดครัวมีดครัว
สกรูไม้สกรูไม้
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
5

Fill and press

Dust the mould and matrix well with talc. Fill the flask with uncured mixed rubber sheet (thick sheet is best, but scraps fuse together), put the plunger on, and press the whole between two blocks of wood screwed together with long wood screws.

วัสดุสำหรับขั้นตอนนี้:

ยางคอมปาวด์ยางคอมปาวด์1 fills the flask

เครื่องมือที่ต้องใช้:

แป้งทัลคัมแป้งทัลคัม
ท่อนไม้เนื้อแข็งท่อนไม้เนื้อแข็ง
สกรูไม้สกรูไม้
6

Heat, top up and cure

Heat the whole in a hot-air chamber. When it reaches the boiling point of water, 212 °F (100 °C), take the flask out and look at the plunger: if it has gone down to its seat without forcing out any rubber, add more rubber. The softened rubber should ooze out round the plunger. Press again and screw the press down, then put it back in the hot chamber, raise the heat to 284 °F (140 °C) and hold it there for half an hour.

เครื่องมือที่ต้องใช้:

เตาอบเตาอบ
ท่อนไม้เนื้อแข็งท่อนไม้เนื้อแข็ง
สกรูไม้สกรูไม้
7

Cut the type apart

Take the mould out, let it cool and open it: the block of type comes out with the letters on one face. Cut it apart into single type with a sharp knife kept wet, worked with a sawing motion. One good matrix can be used many times.

เครื่องมือที่ต้องใช้:

มีดครัวมีดครัว
น้ำน้ำ

วัสดุ

1

เครื่องมือที่จำเป็น

15

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...