ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Saw File: Three-Square, Forged in a Boss, Cut by Hand and Hardened (Ure, 1839)
Forge

สร้างโดย

Forge

4. พฤศจิกายน 2026NO
25
0
0
0
0

Saw File: Three-Square, Forged in a Boss, Cut by Hand and Hardened (Ure, 1839)

The file for sharpening saw teeth as Sheffield made it by hand: a three-square (triangular) bar of cast steel, not tapering, forged in a V-shaped boss, its teeth cut one by one with a chisel and hammer, then hardened under a coat of animal carbon and salt and quenched in cold spring water. Ure says saw files in particular should be hardened with the carbon mixture, so they will cut iron and steel. Not given: sizes and teeth per inch. Source: A. Ure, Dictionary of Arts, Manufactures, and Mines (1839), File. Picture: our drawing.
ขั้นสูง
Unknown

คำแนะนำ

1

Forge the blank

Draw cast steel out square at the forge, then lay it with one angle down in a boss whose recess has two sides meeting at an angle, so the hammer forms one side and the boss the other two. Keep it the same size along its length (saw files are not tapered).

วัสดุสำหรับขั้นตอนนี้:

เหล็กกล้าเบ้าหลอมเหล็กกล้าเบ้าหลอม1 cast steel bar
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ1 ชิ้น

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
คีมช่างตีเหล็กคีมช่างตีเหล็ก
แม่พิมพ์กลมล่าง (สเวจล่าง)แม่พิมพ์กลมล่าง (สเวจล่าง)
ค้อนค้อน
ค้อนปอนด์ค้อนปอนด์
2

Cut the teeth

On an anvil with a flat, even face, hold the file down with a leather strap over each end, the workman's feet in the straps like stirrups. Cut the teeth with a chisel a little broader than the file, sharpened to about 20 degrees, struck with a hammer of 1 to 6 lb. For single cut, run a fine file lightly over the teeth to take off the roughness; for double cut, cut a second set nearly at right angles to the first.

เครื่องมือที่ต้องใช้:

ทั่งเหล็กทั่งเหล็ก
สายหนังสายหนัง
สกัดเย็นสกัดเย็น
ค้อนค้อน
ตะไบโลหะตะไบโลหะ
3

Cut the other sides

To cut the next side, lay the file in a piece of lead-tin alloy with an angular groove, so the teeth already cut are not spoiled on the anvil.

เครื่องมือที่ต้องใช้:

ตะกั่วบัดกรีดีบุก-ตะกั่วตะกั่วบัดกรีดีบุก-ตะกั่ว
ทั่งเหล็กทั่งเหล็ก
สกัดเย็นสกัดเย็น
ค้อนค้อน
4

Coat for hardening

Distil shoemakers' and curriers' leather refuse in an iron still and powder the bright coal left. Grind about equal parts by bulk of this carbon and salt to the consistence of cream with water and cover the file with it.

เครื่องมือที่ต้องใช้:

หม้อกลั่นเหล็กหม้อกลั่นเหล็ก
เกลือเกลือ
น้ำน้ำ
5

Harden

Hold the file by the tang in a fire of very small cokes, drawing it out often, until it is an even cherry red from tang to point. Plunge it straight down, quickly, into clear spring water as cold as possible.

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ถ่านโค้กโลหการถ่านโค้กโลหการ
คีมช่างตีเหล็กคีมช่างตีเหล็ก
น้ำน้ำ
6

Clean and oil

Brush the file with water and powdered cokes until clean and metallic, wash it in two or three waters to take off all the salt, dip it in lime-water, dry it quickly before the fire and oil it while warm with olive oil containing a little oil of turpentine.

เครื่องมือที่ต้องใช้:

ถ่านโค้กโลหการถ่านโค้กโลหการ
น้ำน้ำ
น้ำปูนใสน้ำปูนใส
น้ำมันมะกอกน้ำมันมะกอก
น้ำมันสนน้ำมันสน

วัสดุ

2

เครื่องมือที่จำเป็น

17

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...