ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Scraper: a Hand Scraper Forged from Octagon Steel (Holford, 1907)
A hand scraper takes paint and grease off boiler plate, cast iron or any other material and leaves a bright, smooth surface. Frederick Holford's 20th Century Toolsmith (1907) forges one from 5/8-inch octagon tool steel: the end is drawn perfectly flat, 1/8 inch thick, about 3 inches long and 1 inch wide, with the end left square so its corners do the cutting. It is hardened hard and no temper is drawn.
The overall length of the bar is not given; that is unknown here.
Source: F. J. Holford, The 20th Century Toolsmith and Steelworker (1907), pp. 176-177 and p. 21 (the hardening bath). Picture: his Fig. 107.
ระดับกลาง
An hour
คำแนะนำ
1
1
Read Holford
Read Holford
"A scraper for taking off paint, grease, etc., off boiler plate or any other material and leave a bright smooth surface, is chiefly made from octagon steel ... for an ordinary scraper 5/8 octagon will do."
2
2
Forge the blade flat
Forge the blade flat
Choose octagon steel to suit the width of scraper wanted; 5/8 inch does for an ordinary one. Forge the end perfectly flat, 1/8 inch thick, about 3 inches long and 1 inch wide, and leave the end perfectly square. The length of the bar left for a handle is not given (unknown).
วัสดุสำหรับขั้นตอนนี้:
เหล็กเครื่องมือแปดเหลี่ยม1 barเครื่องมือที่ต้องใช้:
เตาตีเหล็ก
ทั่ง
ค้อนช่างตีเหล็ก
คีมช่างตีเหล็ก
ขนาดที่ไม่ทราบ3
3
Harden, no temper
Harden, no temper
Heat about 1 inch back from the scraping edges and quench in the hardening bath, then cool the whole tool. Holford's bath (p. 21) is clean water free from grease, best made a brine with as much salt as it will dissolve, large and cold. Draw no temper: the tool must be very hard.
เครื่องมือที่ต้องใช้:
เตาตีเหล็ก
คีมช่างตีเหล็ก
น้ำเกลืออิ่มตัว
ถุงมือกันความร้อน4
4
Grind the corners
Grind the corners
Grind the square end so its corners are very sharp: the corners are the scraping edges.
เครื่องมือที่ต้องใช้:
หินลับแบบหมุน5
5
History and honest limits
History and honest limits
Holford says the scraper "will give excellent results if properly forged, hammered and hardened". The same hard, untempered scraper is the tool used to bring metal surfaces true by scraping off high spots.
The overall length of the bar is not given.
วัสดุ
1- ตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
8- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้
