การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Screw Eye: Parmelee's One-Piece Wire Eye with a Stop-Ring
Forge

สร้างโดย

Forge

26. ตุลาคม 2026NO
26
0
0
0
0

Screw Eye: Parmelee's One-Piece Wire Eye with a Stop-Ring

A screw eye bent from one piece of wire, by Arthur W. Parmelee of Worcester, Massachusetts (US 350,209, 1886). One end is threaded to turn into wood, the other bent into a closed eye. His addition is a ring closed into a groove around the shank: it stops the screw at the right depth, looks neat, and is left a little loose so the eye can turn without marking the wood under it. The patent gives no metal or sizes. Iron wire, the 3 mm size, the pliers and the die are ours. The picture: Figs. 1-3 and 10-11 of the patent.
เริ่มต้น
30 minutes

คำแนะนำ

1

Cut a piece of wire

Cut a straight piece of iron wire about 3 mm thick (ours), long enough for the screw, the shank and the eye (Fig. 1).

วัสดุสำหรับขั้นตอนนี้:

ลวดเหล็กดัดลวดเหล็กดัด1 ชิ้น

เครื่องมือที่ต้องใช้:

ไม้บรรทัดไม้บรรทัด
คีมตัดลวดปากเฉียงคีมตัดลวดปากเฉียง
2

Cut the groove

File a narrow groove right round the wire, a screw length from one end (Fig. 2). Parmelee cuts it or presses it in.

เครื่องมือที่ต้องใช้:

ชุดตะไบเข็มชุดตะไบเข็ม
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
3

Point the screw end

File that end to a tapering point (Fig. 3).

เครื่องมือที่ต้องใช้:

ตะไบโลหะตะไบโลหะ
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
4

Thread the screw end

Cut a screw thread on the pointed end "in the usual way". Ours: a die in a die stock, run on as far as the point allows.

เครื่องมือที่ต้องใช้:

ด้ามจับดายเกลียวด้ามจับดายเกลียว
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
5

Bend the eye

Bend the other end into a closed round eye, the end turned in against the shank (Fig. 10).

เครื่องมือที่ต้องใช้:

คีมปากกลมคีมปากกลม
คีมปากแบนคีมปากแบน
6

Make the split ring

Bend a short piece of the same wire round into an open ring that just slips over the shank (Figs. 9 and 11).

วัสดุสำหรับขั้นตอนนี้:

ลวดเหล็กดัดลวดเหล็กดัด1 ชิ้น

เครื่องมือที่ต้องใช้:

คีมตัดลวดปากเฉียงคีมตัดลวดปากเฉียง
คีมปากกลมคีมปากกลม
7

Close the ring into the groove

Slide the ring onto the groove and squeeze it until its two ends meet in a continuous band. Leave it a little loose, so the eye turns while the ring stays still against the wood.

เครื่องมือที่ต้องใช้:

คีมปากแบนคีมปากแบน
8

Turn it into the wood

Turn the screw into the wood by the eye until the ring meets the surface: the ring is the depth stop. Parmelee also allows washers under the ring; we leave them out.

วัสดุ

1

เครื่องมือที่จำเป็น

8

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...