ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Steel Dowel Pins: Two from One Piece, Necked, Hardened and Ground (Stanley 1919)
Frank A. Stanley · Public domain (1919)
Forge

สร้างโดย

Forge

27. ตุลาคม 2026NO
19
0
0
0
0

Steel Dowel Pins: Two from One Piece, Necked, Hardened and Ground (Stanley 1919)

Die makers made their own dowel pins two at a time: one piece of steel is turned, necked in the middle, hardened, ground dead straight to size from each end, then snapped in two at the neck. Frank Stanley described the practice of one die shop. Source: F. A. Stanley, Punches and Dies (1919), pp. 417–419. The choice of tool steel and the forge for hardening are ours; the passage gives no hardening heat. Picture: Stanley's Fig. 610, grinding dowel pins.
ระดับกลาง
1 day

คำแนะนำ

1

Cut stock for two pins

Take a length of steel a little larger than the dowel size and long enough for two pins. It must harden, so use tool steel (our choice).

วัสดุสำหรับขั้นตอนนี้:

เหล็กเครื่องมือแปดเหลี่ยมเหล็กเครื่องมือแปดเหลี่ยม1 length for two pins

เครื่องมือที่ต้องใช้:

ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
2

Turn 0.008 in over size

Turn it on centres to about 0.008 in above the finished size.

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
ตัวพาหมุนงานกลึงตัวพาหมุนงานกลึง
ไมโครมิเตอร์ไมโครมิเตอร์
3

Neck it in the middle

Cut a neck 1/16 in deep in the middle, the dividing line between the two pins.

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
4

Harden

Harden the piece. This passage gives no heat; heat to hardening heat and quench in the usual way for your steel (ours).

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
คีมคีบคีมคีบ
ถังชุบน้ำถังชุบน้ำ
5

Grind each half to size

Put it on dead centres in the grinding machine and grind the diameter to size from one end to the neck. Reverse it on the centres and grind from the other end. The pins come out perfectly straight from end to end.

เครื่องมือที่ต้องใช้:

เครื่องเจียระไนทรงกระบอกเครื่องเจียระไนทรงกระบอก
ตัวพาหมุนงานกลึงตัวพาหมุนงานกลึง
ไมโครมิเตอร์ไมโครมิเตอร์
6

Break the pins apart

Break the piece apart at the neck. You have two dowel pins ground closely to standard size; ream their holes true and straight to fit.

เครื่องมือที่ต้องใช้:

ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ

วัสดุ

1

เครื่องมือที่จำเป็น

8

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...