ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
55-Gallon Open-Head Steel Drum to ICC Specification 17H (1964)
Youblob · CC0
Forge

สร้างโดย

Forge

27. ตุลาคม 2026NO
22
0
0
0
0

55-Gallon Open-Head Steel Drum to ICC Specification 17H (1964)

The open-top 55-gallon (208-litre) steel drum, built to the rule US railways and shippers used for single-trip removable-head drums: welded low-carbon steel body, three rolled hoops, a crowned bottom, and a lid clamped by a bolted ring over a gasket. Source: ICC Specification 17H, 49 CFR 78.118, Federal Register, 29 December 1964. The spec does not say how the bottom is joined. The litre figure, the gasket rubber and the machines are ours. Picture drawn by Youblob.
ขั้นสูง
Production line

คำแนะนำ

1

Cut low-carbon steel sheets

Use low-carbon steel for body and heads. For a 55-gallon drum: body 18 gauge, bottom head 18 gauge, removable head 14 gauge (16 gauge if the cover has one or more corrugations near its edge). 18 gauge is 0.0478 in nominal and at least 0.0428 in; 14 gauge 0.0747 in and at least 0.0677 in, measured at least 3/8 in from an edge.

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กกล้าละมุนแผ่นเหล็กกล้าละมุน1 body, bottom and lid sheets

เครื่องมือที่ต้องใช้:

กรรไกรตัดโลหะงานหนักกรรไกรตัดโลหะงานหนัก
ไมโครมิเตอร์ไมโครมิเตอร์
2

Roll and weld the body

Roll the body sheet into a cylinder and weld the seam. The body seam must be welded.

เครื่องมือที่ต้องใช้:

เครื่องม้วนแผ่นเหล็กเครื่องม้วนแผ่นเหล็ก
เครื่องเชื่อมตะเข็บท่อเครื่องเชื่อมตะเข็บท่อ
3

Roll in three hoops

Roll or swage three hoops into the body, one of them near the top curl.

เครื่องมือที่ต้องใช้:

ลูกกลิ้งรีดบัวลูกกลิ้งรีดบัว
4

Press crowned heads

Press the bottom head crowned (convex) by at least 3/8 in, not standing out beyond the level of the chime, and fit it to the body. The spec does not say how the bottom is joined.

เครื่องมือที่ต้องใช้:

เครื่องปั๊มโลหะเครื่องปั๊มโลหะ
5

Make the bolted ring and gasket

Make the closing ring from 12-gauge steel with drop-forged lugs, one of them threaded, and a 5/8 in bolt and nut (for drums over 30 gallons). Fit a gasket under the lid: gaskets are required.

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กกล้าละมุนแผ่นเหล็กกล้าละมุน1 12-gauge strip for the ring
เหล็กเส้นกลมเหล็กกล้าละมุนเหล็กเส้นกลมเหล็กกล้าละมุน1 for the lugs
ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด1 5/8 in bolt
น็อตหกเหลี่ยมน็อตหกเหลี่ยม1 5/8 in
แผ่นยางแผ่นยาง1 gasket

เครื่องมือที่ต้องใช้:

เครื่องม้วนแผ่นเหล็กเครื่องม้วนแผ่นเหล็ก
ค้อนตกพร้อมแม่พิมพ์ตีขึ้นรูปค้อนตกพร้อมแม่พิมพ์ตีขึ้นรูป
มีดคัตเตอร์งานประดิษฐ์มีดคัตเตอร์งานประดิษฐ์
6

Check capacity and mark

The drum must hold at least 4 % more than its marked 55 gallons, and no more than 5 % more (or 4 % plus 1 quart, whichever is greater). Emboss the marks: ICC-17H, STC (single-trip container), the maker, and the gauges, capacity and year.

เครื่องมือที่ต้องใช้:

เครื่องปั๊มโลหะเครื่องปั๊มโลหะ
7

Leak-test every drum

Test each drum by air pressure inside of at least 7 psi with its seams under water or covered with soapsuds or heavy oil. Reject leakers, or repair them the way they were made and test again.

วัสดุสำหรับขั้นตอนนี้:

น้ำน้ำ1 as required

เครื่องมือที่ต้องใช้:

ปั๊มลมปั๊มลม
เกจวัดความดันเกจวัดความดัน
8

Type tests every four months

On drums taken at random and closed as for use: drop one filled with water to 98 % from 4 ft onto concrete so it lands diagonally on the chime, and hold another at 15 psi water pressure for 5 minutes. None may leak.

วัสดุสำหรับขั้นตอนนี้:

น้ำน้ำ1 as required

เครื่องมือที่ต้องใช้:

เกจวัดความดันเกจวัดความดัน

วัสดุ

6

เครื่องมือที่จำเป็น

10

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...