ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Star Valve-Dash Churn: A Lever Drives a Close-Fitting Perforated Dash, Its Centre Valve Shuts Going Down and Opens Coming Up
J. V. Stevens of Pomeroy, Ohio, received US 31,338, dated 5 February 1861, for "J. V. Stevens's Star Churn". A perforated dash fits the straight-sided body closely and is worked up and down by a lever on an arm at the rim. A loose perforated valve under the dash shuts its large centre opening on the down stroke, forcing the cream up through the holes, and drops open on the up stroke so the cream runs back down through the middle.
The patent gives no sizes; every size here is ours.
ระดับกลาง
About 2 days
คำแนะนำ
1
1
How hard the cream is driven through the holes
How hard the cream is driven through the holes
กำลังโหลดสมุด Jupyter…
2
2
A lever working the upright dash, eight months before
A lever working the upright dash, eight months before
Cooper drives the old dasher by levers on a post. Stevens's lever works a dash that fits the body with a valve in it.
3
3
Read US 31,338
Read US 31,338
"... provided with a valve as at G which closes the aperture L, Fig. 2, upon the downward pressure of the lever C, Fig. 1, which causes the cream to be forced up through the perforations m in the dash and valve and upon the upward motion of the lever C the cream passes freely down through the aperture L and is again forced up through the perforations m, &c., which creates a violent agitation of the cream."
4
4
Body A, hoop and arm B
Body A, hoop and arm B
Use a straight-walled stainless stockpot about 280 mm across inside and 300 deep as the body A: the patent asks for one "of a uniform size inside from top to bottom". Bend a 3 mm stainless strip 25 mm wide into a hoop that clamps round the pot 20 to 45 mm below its rim, closed with a bolt and lock nut. Bolt to it an arm B of the same strip rising 290 mm beside the pot and bent out 35 mm to the pivot, 165 mm from the pot's centre, bored 8.4 mm for the pin I.
วัสดุสำหรับขั้นตอนนี้:
หม้อใบใหญ่1 ชิ้น
แถบเหล็กกล้าไร้สนิมรีดเย็น (420)1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาด3 ชิ้น
นอตล็อกไนลอน3 ชิ้น
แหวนรองแบน3 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
ปากกาจับชิ้นงานหน้าโต๊ะ
สว่านไร้สาย
ชุดดอกสว่าน
ประแจเลื่อน
ตลับเมตร5
5
Dash F with aperture L and bows E
Dash F with aperture L and bows E
Cut a 6 mm HDPE dash F 278 mm across, 1 mm smaller than the pot inside, with a 120 mm aperture L at its centre. Bore 18 mm holes m in two rings, 14 on a 176 mm circle and 20 on a 236 mm circle. Bend four strips of stainless strip 20 mm wide into bows E rising 76 mm, screw their feet to the dash just outside the aperture, and screw their tops to a hardwood collar 48 mm across glued on the stem 70 mm above the dash.
วัสดุสำหรับขั้นตอนนี้:
แผ่น HDPE1 ชิ้น
แถบเหล็กกล้าไร้สนิมรีดเย็น (420)1 ชิ้น
สกรูไม้12 ชิ้น
แผ่นไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้นเครื่องมือที่ต้องใช้:
เข็มทิศ
เลื่อยจิ๊กซอว์
ชุดดอกสว่านใบพาย
สว่านไร้สาย
ชุดดอกสว่าน
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
ปากกาจับชิ้นงานหน้าโต๊ะ
ชุดไขควง6
6
Print the valve G
Print the valve G
The valve G: a disk 150 mm across and 6 thick with eight 12 mm holes, and its sleeve P, 40 mm across and 16 high, with a 30 mm bore that slides easily on the stem. PETG, 0.2 mm layers, 30 % infill, 4 walls.
7
7
Stem D, valve G and pin h
Stem D, valve G and pin h
Cut a 28 mm hardwood dowel 480 mm long as the stem D and flatten its top 55 mm to a tongue 12 mm thick, bored 8.4 mm across 25 mm from the top for the pin j. Slide on the dash's collar, then from below the valve G, sleeve upward, and drive a 6 mm stainless pin h through the stem 40 mm under the dash, so the valve can drop about 30 mm open and rise to shut the aperture.
วัสดุสำหรับขั้นตอนนี้:
เดือยไม้เนื้อแข็ง1 ชิ้น
เส้นใย PETG1 ชิ้น
แท่งสเตนเลส1 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
ชุดสิ่วไม้
สว่านไร้สาย
ชุดดอกสว่าน
เลื่อยตัดเหล็ก8
8
Lever C and pins I and j
Lever C and pins I and j
Cut a hardwood lever C 40 x 30 mm and 615 mm long, rounded at one end. Bore it 8.4 mm across 20 mm from that end for the pin I. Chisel a mortise 13 mm wide and 42 long through it, 150 to 192 mm from the pin hole, for the stem's tongue, and a slot 8.4 mm wide, 160 to 184 mm, through its sides for the pin j. Pin the lever to the arm B with an 8 mm stainless pin I and split pins, the tongue up through the mortise, and the 8 mm pin j through the slot and tongue.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
แท่งสเตนเลส1 ชิ้น
สลักผ่า4 ชิ้น
แหวนรองแบน2 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
ชุดสิ่วไม้
สว่านไร้สาย
ชุดดอกสว่าน
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)9
9
The build in 3D
The build in 3D
FreeCAD model of this build, the pot cut open: the hoop and arm, the lever on its pin, the stem with its tongue and pin, the dash with its holes, aperture and bows, and the valve hanging open on its pin.
10
10
Churn
Churn
Pour about 13 litres of heavy cream at about 15 °C, checked with the thermometer, into the pot, lower the dash in, and pin the lever. Work the lever down and up through its full stroke, briskly, timing it. When the butter comes, unpin the lever, lift the dash out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด13 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่11
11
Troubleshooting
Troubleshooting
Valve-dash churn troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**J. V. Stevens** of Pomeroy, Meigs County, Ohio, US 31,338, 5 February 1861, "Churn", which he called "J. V. Stevens's Star Churn". He claimed "the perforated valve dash to be worked with or without a lever", and wrote that it produced butter "under favorable circumstances in one and a half minutes by the clock"; we have not tested that. He preferred stoneware for the body, with a recess at the top for the hoop; ours is a stainless stockpot with a clamped hoop. His text says the body is of a uniform size inside, though Fig. 1 draws it tapering; we follow the text, which the close-fitting dash needs. The patent gives no sizes; every size here is ours.
วัสดุ
16- 1 ชิ้นตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- 5 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 12 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 13 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
18- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
2พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

Spring-Lever Dasher Churn: A Hand Lever and a Faster Bar on a Post Drive the Old Dasher Down, a Rubber Spring Lifts It
โดย Buttercup
งานไม้
8
0
0
0
0
0

Slotted-Gate Dash Churn: A Hand Wheel Turns a Crank Pin in the Slot of a Sliding Gate, Which Drives the Dash Up and Down
โดย Buttercup
งานไม้
7
0
0
0
0
0

Spatter-Guard Spring Dasher Churn: A Funnel-and-Bowl Block on the Lid Keeps the Cream In, a Spring Lifts the Dasher
โดย Buttercup
งานไม้
5
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
โดย TheChef
งานฝีมือ
63
0
0
0
0
0
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

