ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Hinged-Arm Frame Churn: An Arm That Swings Back Holds the Dasher's Top, Its Forked Brace Holds the Cover Down
John Stilwell of Griffin, Georgia, received US 32,388, dated 21 May 1861, for a stand that turns the dasher of an upright churn. The churn stands on a base in front of a frame; an arm fixed to a cross bar turning in the frame's top reaches over it and holds the dasher's top, while a crank shaft on the frame turns the dasher through bevel gearing. A forked brace hinged to the arm presses the two half covers and the churn down. Turn the brace up to look in, or loosen two buttons and swing the arm back to take the churn out.
The patent gives no sizes; every size here is ours.
ระดับกลาง
About 3 days
คำแนะนำ
1
1
Swinging the arm clear
Swinging the arm clear
กำลังโหลดสมุด Jupyter…
2
2
A hinged bearing over the churn, a year before
A hinged bearing over the churn, a year before
Mitchell hangs the dasher from a hinged journal box. Stilwell steps it in the churn and holds its top in an arm that swings back.
3
3
Read US 32,388
Read US 32,388
"By means of the forked brace bar the churn is held in position in the frame without other fastening and the cover firmly fastened thereon, thus preventing the cream from being thrown out by the action of the beaters. The brace bar also serves to steady the end of the arm in which the beater shaft is stepped."
4
4
Base B, uprights C and cross ties D, D', D''
Base B, uprights C and cross ties D, D', D''
Glue up a hardwood base B 400 x 600 x 30 mm. Mortise four hardwood uprights C 40 x 40 mm, 603 long, into it at the back, 220 mm apart side to side, in pairs 100 mm apart front to back, 230 mm behind where the churn's centre will be. Join each side pair at the top with a cross tie D 40 x 30, 160 long, bored 20.6 mm across 40 mm from its front end for the cross bar's journals; join the front pair with a cross tie D' 260 long, 30 below the top; and join each pair 430 mm up with a cross tie D'' 260 x 40 x 20 for the crank shaft's boxes.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง4 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้24 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
ชุดสิ่วไม้
เราเตอร์
สว่านไร้สาย
ชุดดอกสว่าน
ชุดดอกสว่านใบพาย
แคลมป์แบบบาร์
ตลับเมตร5
5
Cross bar F, arm G, buttons O, O' and brace bar M
Cross bar F, arm G, buttons O, O' and brace bar M
Run a 20 mm stainless rod 270 mm long as the cross bar F through both cross ties D. Cut a hardwood arm G 40 x 30 mm, 310 long, bore it across 20.4 mm 20 mm from its back end, and pin it on F so it reaches forward over the churn's centre resting on the tie D'. Glue a hardwood block 40 x 40 x 40 under its front end, bored 16.6 mm 30 deep from below for the staff's top. Screw two hardwood buttons O, O' on the tie D' either side of the arm, to turn over it. For the brace bar M, cut two hardwood legs 20 x 20 mm, 250 long, and a foot bar 110 x 20 x 12 notched for the staff, and hang the legs either side of the arm on a 12 mm stainless pin through it above the staff, so the foot presses the cover.
วัสดุสำหรับขั้นตอนนี้:
แท่งสเตนเลส2 ชิ้น
แผ่นไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้6 ชิ้น
สลักผ่า4 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สาย
ชุดดอกสว่าน
ชุดดอกสว่านใบพาย
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
ชุดไขควง6
6
Print the step
Print the step
The step in the churn's bottom: 40 mm across, 12 high, with a 16.8 mm hole 8 deep. PETG, 0.2 mm layers, 30 % infill, 4 walls.
7
7
Print the pinion b
Print the pinion b
The pinion on the staff: 14 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
8
8
Print the bevel wheel K
Print the bevel wheel K
The driving wheel K: a crown wheel of 42 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
9
9
Churn A, covers, staff L, shaft H, wheel K and crank J
Churn A, covers, staff L, shaft H, wheel K and crank J
Use a 20-litre food-grade bucket as the churn A on the base in front of the frame, with the step in its bottom. Cut a 12 mm HDPE cover to it and saw it in two halves through a 17 mm centre hole. Cut a 16 mm stainless staff L 586 mm long, screw two crossed hardwood slats 240 x 30 x 8 mm on hubs 70 and 170 mm above its foot as the dasher, and pin the pinion b on it 420 mm above the churn's floor. Screw two hardwood boxes I, I' 50 x 24 x 47 mm on the D'' ties, bored 16.6 mm across 23 mm above them. Run a 16 mm stainless shaft H 410 mm long through them with the wheel K pinned on its front end meshing b, a shaft collar behind the front box, and a crank J of mild steel flat bar, 100 mm throw, with a hardwood handle at the back.
วัสดุสำหรับขั้นตอนนี้:
ถังขนาด 20 ลิตร1 ชิ้น
แผ่น HDPE1 ชิ้น
แท่งสเตนเลส2 ชิ้น
แผ่นไม้เนื้อแข็ง1 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้น
สกรูไม้8 ชิ้น
Shaft Collar1 ชิ้น
สลักผ่า3 ชิ้น
เหล็กแบนกล้าละมุน1 ชิ้น
เส้นใย PETG1 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เข็มทิศ
เลื่อยจิ๊กซอว์
ชุดดอกสว่านใบพาย
สว่านไร้สาย
ชุดดอกสว่าน
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
ปากกาจับชิ้นงานหน้าโต๊ะ
ชุดไขควง10
10
The build in 3D
The build in 3D
FreeCAD model of this build, the churn cut open: the base and frame, the cross bar with the arm and its bearing block, the buttons, the forked brace bar on the covers, the staff with its slats and pinion, and the crank shaft with the bevel wheel running back through the frame to the crank.
11
11
Churn
Churn
With the arm turned back, stand the churn on the base with the staff in its step, pour in about 10 litres of heavy cream at about 15 °C, checked with the thermometer, and lay on the half covers. Swing the arm down over the staff's top, turn the buttons over it and let the brace bar rest on the covers. Turn the crank steadily, timing it. To look in, turn the brace up and lift a half cover. When the butter comes, turn the buttons, swing the arm back, lift out the staff, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด10 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่12
12
Troubleshooting
Troubleshooting
Hinged-arm churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**John Stilwell** of Griffin, Spalding County, Georgia, US 32,388, 21 May 1861, "Churn". He claimed "the combination of the brace bar M, hinged arm G, buttons O, O', with a vertical barrel churn and rotary dasher shaft L". He neither drew nor described the dasher on the shaft; ours is two crossed slats. His churn was a hooped barrel and his gears bevel wheels; ours are a bucket and a printed crown wheel and pinion. The patent gives no sizes; every size here is ours.
วัสดุ
14- 4 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 38 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 7 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 10 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
19- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
4พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

Geared Crank-Frame Churn: A Frame Over an Ordinary Churn Gears a Hand Crank Up to Drive a Grated Dasher by Pitman
โดย Buttercup
งานไม้
8
0
0
0
0
0

Hung-Dasher Churn: The Dasher Hangs in a Long Hinged Journal Box Above the Lid, No Step in the Tub
โดย Buttercup
งานไม้
7
0
0
0
0
0

Toothed-Disk Pass Churn: Cream Poured In Passes Once Between Fixed Toothed Disks and a Toothed Wheel Spinning Between Them
โดย Buttercup
งานไม้
13
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
โดย TheChef
งานฝีมือ
63
0
0
0
0
0
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

