ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Stone Carving Hammer: a Granite Cutters' Mash Hammer (Holford, 1907)
A mash hammer is a two-faced hammer used by granite cutters. H. Holford's 20th Century Toolsmith and Steelworker (1907) gives the granite cutters' pattern: forged from 75-point carbon steel 1 3/4 inches square, with a small round eye, both ends bevelled and hardened, with no temper drawn.
His forging and hardening come from his chapter on the hand hammer. The brine bath comes from his chapter on the hardening bath. He gives no weight or length for the mash hammer and no handle wood; those are unknown here.
Source: H. Holford (1907), pp. 21, 47-53, 127-128. Picture: his Fig. 66.
ระดับกลาง
A day
คำแนะนำ
1
1
Read Holford
Read Holford
"After proper hardening it is not necessary to draw any temper as there are no sharp corners to break off."
2
2
Heat the steel
Heat the steel
Take good steel of 75 point carbon (about 0.75 per cent), 1 3/4 inches square; the length for a given weight is not given (unknown). In a good clean fire, heat it slowly, turning it now and then so the corners do not overheat while the middle is still black, until it is an even yellow heat right through.
วัสดุสำหรับขั้นตอนนี้:
เหล็กเครื่องมือสี่เหลี่ยมจัตุรัส1 1 3/4 in squareเครื่องมือที่ต้องใช้:
เตาตีเหล็ก
คีมช่างตีเหล็ก
ขนาดที่ไม่ทราบ
ถุงมือกันความร้อน3
3
Punch a small round eye
Punch a small round eye
Punch a small round eye, not the large oval eye of other hammers, no more than 3/4 inch across when finished. Start it a little smaller, as the eye grows while the hammer is forged. A little coal dust in the hole keeps the punch from sticking.
เครื่องมือที่ต้องใช้:
เหล็กตอกร้อน
ค้อนช่างตีเหล็ก
ทั่ง
คีมช่างตีเหล็ก
แว่นนิรภัย4
4
Forge the bevelled ends
Forge the bevelled ends
Forge both ends bevelled down from the eye on the top and sides, leaving the bottom side perfectly flat (Fig. 66). Bevel the face at each end too, dress it a little full in the centre and leave the corners very rounded. Start at an even yellow heat and work lower as you finish, ending at a dark dull red; steel worked too cold is strained and may crack in hardening. Anneal it if much filing is to be done.
เครื่องมือที่ต้องใช้:
ค้อนช่างตีเหล็ก
ฟุลเลอร์ (เหล็กเซาะร่อง)
ทั่ง
เตาตีเหล็ก
คีมช่างตีเหล็ก
แว่นนิรภัย5
5
Harden both ends
Harden both ends
With the coal well charred and free from sulphur and thick smoke, stand one end upright in the fire and heat it slowly and evenly. If the corners get hot enough to harden before the centre, stop blowing until the centre is cherry red too. Heat no more than 3/4 inch back from the end and never harden the eye. Plunge the whole hammer in the hardening bath and hold it there until stone cold. Holford's bath (p. 21) is clean water free from grease, best made into a brine with as much salt as it will dissolve, kept as large and cold as possible. Do the same with the other end. Draw no temper.
เครื่องมือที่ต้องใช้:
เตาตีเหล็ก
คีมช่างตีเหล็ก
น้ำเกลืออิ่มตัว
ถุงมือกันความร้อน6
6
Hang it
Hang it
Fit a good straight handle through the eye; Holford adds that a little spring in it is a good fault. He does not name the wood (unknown).
วัสดุสำหรับขั้นตอนนี้:
วัสดุที่ไม่ทราบ1 handle7
7
History and honest limits
History and honest limits
Holford wrote for blacksmiths and toolsmiths who dressed quarry and granite tools; the same page describes the granite hammer, drawn to a sharp edge at both ends and tempered to a light straw. He blames broken corners and hollow faces on steel soaked too long or worked too cold, and on the old way of dipping only an inch of the end, which leaves the face hollow.
The size of the mash hammer and the handle wood are not given; the tools are ours.
วัสดุ
2- 1 1 3/4 in squareตัวยึดตำแหน่ง
- 1 handleตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
10- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้
