ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Stone Flat Chisel: the Marble Lettering Tool, Drawn Very Thin (Holford, 1907)
Forge

สร้างโดย

Forge

5. พฤศจิกายน 2026NO
22
0
0
0
0

Stone Flat Chisel: the Marble Lettering Tool, Drawn Very Thin (Holford, 1907)

A flat chisel for cutting letters in marble. Frederick Holford's 20th Century Toolsmith (1907) makes marble tools like granite tools, from 7/8-inch octagon steel, but tempers them a little harder, to a very light straw. The lettering tool is drawn out very thin (his Fig. 69); because of that thinness it must be heated with great care, and the last few blows when dressing it are struck on the flat side only, at a very low heat. He gives no edge width, length or carbon content; those are unknown here. Source: F. J. Holford, The 20th Century Toolsmith and Steelworker (1907), p. 130, pp. 122-123 and p. 21 (the hardening bath). Picture: his Fig. 69.
ระดับกลาง
An hour

คำแนะนำ

1

Read Holford

"Lettering tools are drawn out very thin, as Fig. 69, but owing to the thinness be very careful when heating, and make sure when dressing to always strike the last few blows on the flat side only, when at a very low heat."
2

Draw out the edge

Forge 7/8-inch octagon steel down to a straight edge, drawn out very thin (Fig. 69). Heat with great care because of the thinness. Strike the last few blows on the flat side only, at a very low heat. Straighten the edge with a very coarse file after hammering. Edge width and length are not given (unknown).

วัสดุสำหรับขั้นตอนนี้:

เหล็กเครื่องมือแปดเหลี่ยมเหล็กเครื่องมือแปดเหลี่ยม1 bar

เครื่องมือที่ต้องใช้:

เตาตีเหล็กเตาตีเหล็ก
ทั่งทั่ง
ค้อนช่างตีเหล็กค้อนช่างตีเหล็ก
คีมช่างตีเหล็กคีมช่างตีเหล็ก
ตะไบโลหะตะไบโลหะ
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
3

Harden and temper

Heat no farther back than 1/2 inch, taking care not to overheat the thin edge. Dip at least an inch deep into the hardening bath (p. 21: clean water, best a brine with as much salt as it will dissolve, large and cold) so the temper runs back slowly, and stop it at a very light straw, the marble temper.

เครื่องมือที่ต้องใช้:

เตาตีเหล็กเตาตีเหล็ก
คีมช่างตีเหล็กคีมช่างตีเหล็ก
น้ำเกลืออิ่มตัวน้ำเกลืออิ่มตัว
ถุงมือกันความร้อนถุงมือกันความร้อน
4

History and honest limits

Holford sets lettering tools apart from the tooth and plain chisels used to dress marble, which "are not drawn out so thin"; the teeth of tooth chisels are filed in after hammering (his Fig. 70). Edge width, length and the carbon of the steel are not given; an octagonal tool steel bar stands for the 7/8-inch octagon steel.

วัสดุ

1

เครื่องมือที่จำเป็น

8

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...