ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Butterfly-Wing Churn: Two Dashers Hinged to an Adjustable Bar Flap Together From One Crank
Josiah Stubbs of Dublin, Indiana, received US 24,673, dated 5 July 1859, for a churn with two dashers hinged to a central bar like a butterfly's wings. The bar slides on notched stays inside the shell and is set so the cream barely covers it. One crank on the side works both dashers through two rods, one crossing the churn on a slant. Going down, the cream rushes round the dashers' edges against the shell; going up, flanges on the dashers carry cream up and throw it together.
This rung builds it in a 20-litre bucket.
ระดับกลาง
About 6 hours, plus printing
คำแนะนำ
1
1
Setting the bar for the cream you have
Setting the bar for the cream you have
กำลังโหลดสมุด Jupyter…
2
2
Hinged, flapping dashers, before it
Hinged, flapping dashers, before it
Kelly flapped hinged dashers by swinging the tub. Stubbs keeps the shell still and flaps them from a crank.
3
3
Read US 24,673
Read US 24,673
"As the dashers are drawn upwardly, a portion of the fluid will be retained upon them, by means of the flanges (e) and thrown violently together as the dashers reach their upper extremity of motion".
4
4
Print the flange
Print the flange
A quarter of a dasher's flange e. Print four. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
5
5
Stays and bar b
Stays and bar b
Screw two hardwood stays a 24 x 15 mm, 337 mm long, upright inside the bucket on opposite sides, and saw notches a' 6 mm wide and 4 mm deep in their inner faces every 20 mm from 60 to 220 mm up. Cut a hardwood bar b 272 x 20 x 16 mm with a slotted block 44 mm wide at each end to slide on the stays, and fit an M5 set screw c with a wing nut through one block to hold it in a notch.
วัสดุสำหรับขั้นตอนนี้:
ถังขนาด 20 ลิตร1 ชิ้น
แผ่นไม้เนื้อแข็ง1 ชิ้น
สกรูไม้6 ชิ้น
กาวไม้1 ชิ้น
สกรูเกลียวมิล1 ชิ้น
น็อตปีกผีเสื้อ1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยมือ
สิ่ว
สว่านไร้สาย
ชุดดอกสว่าน
ชุดไขควง
ตลับเมตร6
6
Dashers d d
Dashers d d
Cut two half-discs 244 mm across from 12 mm plywood and trim each to 220 mm along its straight edge. Glue the printed flanges e round their curved edges, standing 15 mm up. Hinge each dasher's straight edge to one side of the bar with two stainless butt hinges, 4 mm clear of the bar. Screw a small hardwood eye block on each dasher 100 mm out from the bar's middle, the right one 30 mm toward the front, the left one 40 mm toward the back.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้อัด1 ชิ้น
เส้นใย PETG1 ชิ้น
กาวไม้1 ชิ้น
บานพับประตู4 ชิ้น
สกรูไม้16 ชิ้น
แผ่นไม้เนื้อแข็ง1 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยจิ๊กซอว์
สว่านไร้สาย
ชุดดอกสว่าน
กระดาษทราย
ชุดไขควง7
7
Crank h k and rods g g'
Crank h k and rods g g'
Drill the bucket's wall 13 mm 315 mm up, 30 mm toward the front, and fit a 12 mm stainless shaft through a hardwood bearing block outside, sealed. Fix a hardwood crank arm h 35 mm between centres on the inner end with a 8 mm pin pointing inward, and a crank handle k outside. Bend two 6 mm stainless rods with an eye at each end: g 185 mm between eyes from the pin to the right dasher, g' 262 mm from the pin across the churn on a slant to the left dasher.
วัสดุสำหรับขั้นตอนนี้:
แท่งสเตนเลส1 ชิ้น
แผ่นไม้เนื้อแข็ง1 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้น
สกรูเกลียวมิล2 ชิ้น
นอตล็อกไนลอน2 ชิ้นเครื่องมือที่ต้องใช้:
สว่านไร้สาย
ชุดดอกสว่าน
ปากกาจับชิ้นงานหน้าโต๊ะ
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
ชุดไขควง8
8
The build in 3D
The build in 3D
FreeCAD model of this build, the near side of the bucket cut away: the notched stays, bar b, the two hinged dashers with their flanges, the crank inside the wall and the two rods, one crossing on a slant. It was checked at eight crank angles.
9
9
Churn
Churn
Pour in about 8 litres of heavy cream at about 15 °C, checked with the thermometer, and set the bar in the notch the notebook gives so the cream barely covers it. Put the lid on and turn the crank steadily; time it. When the butter comes, lift the bar and dashers out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด8 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่10
10
Troubleshooting
Troubleshooting
Butterfly-wing churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Josiah Stubbs** of Dublin, Wayne County, Indiana, US 24,673, 5 July 1859, "Churn". He claimed working the butterfly wings with a single crank on one side, the rod g' crossing the cylinder on a slant. He gave no sizes or materials: every size, the notches' spacing and the crank's throw are ours.
วัสดุ
16- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 22 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 8 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
16- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
2พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้



