การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Thimble: the Pitted Iron Thimble Gilt Inside (Rouy and Berthier, Ure 1839)
Forge

สร้างโดย

Forge

4. พฤศจิกายน 2026NO
13
0
0
0
0

Thimble: the Pitted Iron Thimble Gilt Inside (Rouy and Berthier, Ure 1839)

The Paris method of Rouy and Berthier: thin sheet-iron discs, red-hot, punched step by step into a cup through five ever-deeper hollows, then turned, pitted and annealed on the lathe, gilt inside with gold leaf pressed on by a steel mandril, and banded outside with a gold fillet. Variable: closed (pitted round end) or open (no end, for tailors). Source: Andrew Ure, Dictionary of Arts, Manufactures and Mines (1839), 'Thimble'. Picture: a modern pitted thimble (Commons, CC BY-SA 3.0).
ขั้นสูง
Unknown

คำแนะนำ

1

Punch the blanks

Cut sheet iron 1/24 in thick into strips sized for the thimbles. Run them under a punch press to cut discs about 2 in across, left joined by a tail, a dozen to a strip.

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็ก (ตีด้วยค้อน)แผ่นเหล็ก (ตีด้วยค้อน)1 1/24 in

เครื่องมือที่ต้องใช้:

เครื่องปั๊มเจาะเครื่องปั๊มเจาะ
2

Sink the cup

Heat the blanks red-hot and lay each on a mandril fitted to its size. Strike the middle with a round-faced punch about as thick as a finger to sink it into the first hollow, then drive it through a block with five hollows of increasing depth until it has the thimble's shape.

เครื่องมือที่ต้องใช้:

เตาตีเหล็กเตาตีเหล็ก
คีมคีบคีมคีบ
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ
ค้อนค้อน
3

Turn and pit on the lathe

Chuck the rough thimble in the lathe, polish the inside, turn the outside, mark the rings for the gold band, and press in the rows of pits with a milling tool.

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
เครื่องมือทำลาย (เนอร์ลิง)เครื่องมือทำลาย (เนอร์ลิง)
4

Anneal, gild and band

Anneal and brighten the thimbles. Line each inside with a thin cone of gold leaf, bonded to the iron by the hard pressure of a smooth steel mandril. Turn an annular seat outside, lay a gold fillet in it and press its edges into a fine groove cut on the lathe.

วัสดุสำหรับขั้นตอนนี้:

ทองคำเปลวทองคำเปลว1 lining
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 gold fillet

เครื่องมือที่ต้องใช้:

เตาตีเหล็กเตาตีเหล็ก
แกนแมนเดรลแกนแมนเดรล
เครื่องกลึงโลหะเครื่องกลึงโลหะ

วัสดุ

3

เครื่องมือที่จำเป็น

8

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...