ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Washing Machine with Churn: One Crank Pounds the Wash, Turns the Tub and Works a Dash Churn (Wagoner & Severson, 1859)
John Wagoner and Abram Severson Jr. of Guilderland Center, New York, received US 25,152, dated 16 August 1859, for a washing machine. A crank shaft with a heavy balance wheel rocks a long lever. A springy beam on the lever carries a pounder into the tub, and a belt and a pair of bevel wheels turn the tub slowly under it. The tub stands on a hinged platform: folded up it slackens the belt, and let down the tub's weight tightens it. A pin on the lever also works the dash of a churn standing beside the machine, with or without the washing.
The patent gives no sizes; every size here is ours.
ขั้นสูง
About 5 days, plus printing
คำแนะนำ
1
1
Crank pin, strokes and tub speed
Crank pin, strokes and tub speed
กำลังโหลดสมุด Jupyter…
2
2
One crank working a churn and a washtub, a year before
One crank working a churn and a washtub, a year before
Swan's machine lifted a plunger by a cam. Here a springy beam carries the pounder, and the tub's own weight tightens the belt that turns it.
3
3
Read US 25,152
Read US 25,152
"In addition to what has now been described our machine is adapted to operate a churn very effectively either alone or simultaneously with the washing operation."
"We place the center of our tube J out of the plane of the motion of the levers T and V. Our pounder therefore inclines to strike on one side of J and not in the center thereby increasing the uniformity of the effect on the contents."
4
4
Print the pulley for shaft D
Print the pulley for shaft D
Flat-faced pulley 120 mm across and 40 mm wide, bored 31 mm for shaft D. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print pulley R
Print pulley R
Flat-faced pulley 100 mm across and 40 mm wide, bored 21 mm for the lower bevel wheel's shaft. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Frame A, legs B and uprights C
Frame A, legs B and uprights C
From 70 x 70 mm timber cut three stringers 1500 mm, two cross pieces 630 mm, four legs 700 mm, an upright 830 mm and an upright 720 mm. Bolt the cross pieces across the tops of the legs and the stringers on the cross pieces, 210 mm apart, so the frame's top is 840 mm from the floor. Bolt the long upright to the outside of the front stringer 100 mm from the left end and the short one 100 mm from the right end. Chisel an opening 50 x 260 mm through the left upright, from 440 to 700 mm above the stringer, and bore it across 560 mm up for pin v (a 16 mm bolt).
วัสดุสำหรับขั้นตอนนี้:
ไม้เนื้ออ่อน 70x70 มม.11 m
สลักเกลียวหัวกลม16 ชิ้น
แหวนรองแบน16 ชิ้น
นอตล็อกไนลอน16 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยมือ
สว่านไร้สาย
ชุดดอกสว่าน
ชุดดอกสว่านใบพาย
สิ่วเจาะเดือย
ค้อนไม้
ฉากตาย
ตลับเมตร
ประแจเลื่อน
แคลมป์แบบบาร์7
7
Shaft D, balance wheel F and crank E
Shaft D, balance wheel F and crank E
Bolt three bearing blocks on the stringers' tops 650 mm from the left end and pass a 30 mm steel shaft D through them, 710 mm long. Build the balance wheel from three layers of 20 mm hardwood segments glued crossways: 840 mm across, a 100 mm rim and four spokes, 50 mm thick in all. Fit it on D between the front and middle stringers, the printed pulley between the middle and back stringers, and a hand crank 240 mm long on the back end. On the front end fit crank E, a hardwood arm 20 mm thick with a slot from 50 to 125 mm out, and a 20 mm bolt in the slot for the crank pin e.
วัสดุสำหรับขั้นตอนนี้:
แท่งสเตนเลส1 ชิ้น
ตุ๊กตาลูกปืน3 ชิ้น
แผ่นไม้เนื้อแข็ง3 ชิ้น
กาวไม้1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาด13 ชิ้น
นอตล็อกไนลอน13 ชิ้น
Shaft Collar2 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยจิ๊กซอว์
เข็มทิศ
เลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สาย
ชุดดอกสว่านใบพาย
เราเตอร์
แคลมป์แบบบาร์
เลื่อยตัดเหล็ก
ประแจเลื่อน8
8
Lever T, link U and rod V
Lever T, link U and rod V
Cut lever T from hardwood 40 x 70 mm, 1195 mm long. Bolt it to the front of the right upright, 610 mm above the stringer, free to rock. Join it to the crank pin by link U, hardwood 20 x 40 mm with its pin holes 560 mm apart, 715 mm from T's pivot. At T's left end join rod V, hardwood 30 x 40 mm, slotted 22 mm wide for 220 mm, and pass it through the left upright's opening astride pin v. Fix a steel pin 3, 24 mm and 370 mm long, through T 1015 mm from its pivot, sticking out at the front for the churn.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง2 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาด4 ชิ้น
แหวนรองแบน8 ชิ้น
นอตล็อกไนลอน4 ชิ้น
แท่งสเตนเลส1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
เราเตอร์
สว่านไร้สาย
ชุดดอกสว่าน
ชุดดอกสว่านใบพาย
เลื่อยตัดเหล็ก
กระดาษทราย
ประแจเลื่อน
ตลับเมตร9
9
Spring beam W and the pounder
Spring beam W and the pounder
Cut the spring beam W from ash 30 x 40 mm, 1210 mm long. Lay it on T's top, its left end against a block glued on T, bolt it through T 415 mm left of the pivot with a wing nut (the hand nut w), and let it run past the upright to overhang the frame by 510 mm. Make rod X from hardwood 40 x 40 mm, 1090 mm long, with four holes at its top for height. Under it glue a hardwood head 200 x 120 mm with five legs 30 x 36 mm, 160 mm long, each slotted (Z) and bored across (z). Hang X from W's end on a bolt so it swings freely, in front of W.
วัสดุสำหรับขั้นตอนนี้:
ไม้กระดานแอช1 ชิ้น
แผ่นไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาด2 ชิ้น
น็อตปีกผีเสื้อ1 ชิ้น
แหวนรองแบน4 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
เราเตอร์
สว่านไร้สาย
ชุดดอกสว่าน
สิ่วเจาะเดือย
ค้อนไม้
กระดาษทราย
แคลมป์แบบบาร์10
10
Hinged platform M, bevel wheels and platform K
Hinged platform M, bevel wheels and platform K
Make platform M from 40 mm hardwood, 860 x 860 mm, and hang it on two strap hinges (the butts m) at the feet of the right-hand legs. On M, 100 mm from the hinges, fit a 20 mm vertical shaft in a flange bearing with pulley R and the lower bevel wheel on it. In a hardwood post fit a 20 mm cross shaft with the upper bevel wheel and a 240 mm hardwood pulley P in line with the pulley on D. 480 mm from the hinges, 340 mm towards the front, set a 24 mm shaft L in a hardwood block that slides in a slot along M, with a compression spring pushing it away from R. Glue platform K, 660 mm across and 40 mm thick, bore it for L, and set four 40 mm hardwood wheels l under its edge.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง4 ชิ้น
กาวไม้1 ชิ้น
บานพับแถบเหล็ก2 ชิ้น
ตลับลูกปืนหน้าแปลน3 ชิ้น
ชุดเฟืองดอกจอก (เหล็กกล้า, 1:1)1 ชิ้น
แท่งสเตนเลส1 ชิ้น
Shaft Collar3 ชิ้น
ชุดสปริงกด1 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้น
สกรูไม้40 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาด4 ชิ้น
นอตล็อกไนลอน4 ชิ้น
เส้นใย PETG1 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยจิ๊กซอว์
เข็มทิศ
เราเตอร์
สว่านไร้สาย
ชุดดอกสว่าน
ชุดดอกสว่านใบพาย
เลื่อยตัดเหล็ก
แคลมป์แบบบาร์
ประแจเลื่อน11
11
Belts O and S, and the fold
Belts O and S, and the fold
Put belt S round pulley R and platform K's rim. Fold M up against the frame, run a string round the pulley on D and pulley P, and choose belt O just short enough that, with M let down and empty, it holds M at a slight angle; "The belt O is sufficiently short to hold the platform M at a slight angle until the weight of J is added thereto." Set the wooden tub J on K: its weight should pull M flat and the belt tight. Oil the wood.
วัสดุสำหรับขั้นตอนนี้:
สายพานขับ2 ชิ้น
อ่างไม้1 ชิ้น
น้ำมันลินสีดต้ม1 ชิ้นเครื่องมือที่ต้องใช้:
ตลับเมตร12
12
The build in 3D
The build in 3D
FreeCAD model of this build: the frame, shaft D with the balance wheel and crank E, lever T with link U and rod V, the spring beam W and the pounder in the tub (front of the tub cut away), the hinged platform M with the bevel wheels, pulleys and belts, and the churn on pin 3. The crank was turned through 18 positions.
13
13
Wash
Wash
Put warm water, soap and the clothes in the tub, and set the pounder's height so its feet clear the tub's bottom by the clothes. Turn the hand crank steadily. The pounder rises and falls on one side of the tub while the tub turns under it, so every part of the wash comes under it in turn. Move the crank pin out in its slot for a longer stroke, in for a shorter one. Lift the clothes out to rinse and wring.
เครื่องมือที่ต้องใช้:
น้ำ
สบู่ก้อน14
14
Churn on pin 3
Churn on pin 3
Make the dash 2: a hardwood rod 35 mm across, 1250 mm long, bored at the top to hang on pin 3, with two crossed blades 220 x 30 x 20 mm at the bottom. Stand the churn under pin 3, beside the machine, pour in about 10 litres of cream at about 15 °C (checked with the thermometer), a third of its height, pass the dash through the lid and hang it on pin 3. Turn the crank, with or without the wash, timing it. When the butter comes, lift the dash off the pin, drain the buttermilk, wash the butter in cold water, salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด10 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
แผ่นไม้เนื้อแข็ง1 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้นเครื่องมือที่ต้องใช้:
ถังปั่นเนย
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่
น้ำ
สว่านไร้สาย
ชุดดอกสว่านใบพาย
เลื่อยมือ15
15
Troubleshooting
Troubleshooting
Washing machine troubleshooting.
Flow
Loading...
16
16
History and honest limits
History and honest limits
**John Wagoner and Abram Severson, Jr.** of Guilderland Center, New York, US 25,152, 16 August 1859, "Washing-Machine". They claimed mounting the platform K and the pulleys and gearing P Q R on the hinged platform M, so turning M up slackens belt O and turning it down lets the tub's weight tighten it. The patent gives no sizes; every size here is ours. Their hand lever H and rod I, a second way to turn D, are not built: we turn D by a crank, which the patent allows. The spring that urges K's centre against belt S is "not represented" in their drawing; ours is a compression spring in a slot.
วัสดุ
24- ตัวยึดตำแหน่ง
- 16 ชิ้นตัวยึดตำแหน่ง
- 28 ชิ้นตัวยึดตำแหน่ง
- 37 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 40 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 10 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
24- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
3พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้





