ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Oblique Box-Dasher Churn: A Hollow Slanted Dasher, Open on Two Sides, Churns Fast and Gathers the Butter Inside It Turned Slow
Buttercup

สร้างโดย

Buttercup

11. พฤศจิกายน 2026IE
9
0
0
0
0

Oblique Box-Dasher Churn: A Hollow Slanted Dasher, Open on Two Sides, Churns Fast and Gathers the Butter Inside It Turned Slow

Moses D. Wells of Morgantown, Virginia, received US 31,756, dated 19 March 1861, for a churn dasher shaped as a slanted open box: two flat end plates carrying the journals, two curved face pieces with lips at opposite corners, and two open sides. It turns on a horizontal axis in a box whose bottom is curved to its sweep. Turned fast it churns; turned the same way slowly, it gathers the butter inside itself, the lips keeping it from being thrown out, so it lifts out in a lump. The patent gives no sizes; every size here is ours.
ระดับกลาง
About 2 days

คำแนะนำ

1

Churning fast, gathering slow

กำลังโหลดสมุด Jupyter…
2

A round-bottomed box with a turning dasher, eight months before

Park's box works the butter with pins. Wells's hollow dasher gathers it inside itself.
3

Read US 31,756

"The dasher being hollow, a few slow turns of the same causes the butter to collect within the box so as to be removed in a lump. ... The object of the diagonal lips b', b', is, to gather the butter against, and prevent it from being thrown out of the box in turning it around."
4

Body B with a curved bottom, legs and lid

Glue up two hardwood ends 22 mm thick, 350 mm wide and 320 tall. On each draw the inside: a 300 mm half circle with its centre 160 mm up, and straight sides rising 150 mm above the centre to the top. Rout a groove 1.6 mm wide and 8 deep on that line. Cut a slot 16.6 mm wide down from the top edge to the centre, rounded at its foot, as the journal bearing, and a hardwood keeper that fills the slot above the journal. Bend a 1.5 mm stainless sheet 416 mm long into a U to fit the line, set it in both grooves with silicone sealant, and screw hardwood sides 22 mm thick outside its straight parts. Screw four hardwood legs 40 x 40 mm, 390 long, to the ends, splayed out. Cut a hardwood lid 444 x 350 x 22 mm, notched over the keepers, with a 25 mm air opening o.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง4 ชิ้น
แผ่นสเตนเลสแผ่นสเตนเลส1 ชิ้น
ซิลิโคนยาแนวซิลิโคนยาแนว1 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สกรูไม้สกรูไม้30 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
เข็มทิศเข็มทิศ
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
เราเตอร์เราเตอร์
ชุดสิ่วไม้ชุดสิ่วไม้
ค้อนยางค้อนยาง
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
แคลมป์แบบบาร์แคลมป์แบบบาร์
ชุดไขควงชุดไขควง
ตลับเมตรตลับเมตร
5

Print the end plates a (two)

An end plate of the dasher: 15 mm thick, the slanted outline of Fig. 1 with curved top and bottom edges, a 50 mm boss at the centre. Print two; drill each 16 mm at the centre for a journal. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
6

Dasher D: end plates a, face pieces b with lips b', journals

Cut two strips of 1.5 mm stainless sheet 360 mm long, each 160 mm wide; bend each to a curve of about 300 mm radius following the end plates' curved edges, with a 20 mm lip b' at one long edge turned on round the corner. Screw them to the end plates' curved edges, the lips at diagonally opposite corners, leaving the two slanted sides open. Push a 16 mm stainless journal into each end plate's boss and pin it: one 40 mm long, the other 90 mm for the crank. Lay the journals in the slots and drop in the keepers. Pin a crank of mild steel flat bar, 120 mm throw, with a hardwood handle, on the long journal.

วัสดุสำหรับขั้นตอนนี้:

เส้นใย PETGเส้นใย PETG1 ชิ้น
แผ่นสเตนเลสแผ่นสเตนเลส1 ชิ้น
สกรูไม้สกรูไม้16 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น
สลักผ่าสลักผ่า3 ชิ้น
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
ค้อนยางค้อนยาง
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ชุดไขควงชุดไขควง
7

The build in 3D

FreeCAD model of this build, cut open: the round stainless bottom in grooved ends with slotted bearings and keepers, the legs and lid with its air opening, and the slanted hollow dasher with its curved, lipped face pieces and crank.
ไฟล์แบบBLENDCC0 - Free
8

Churn and gather

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the box, so it stands below the axis, and put on the lid. Turn the crank briskly, timing it. When the butter comes, turn the same way slowly for a few turns until it gathers inside the dasher. Lift off the lid and keepers, lift the dasher out by its journals, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

วัสดุสำหรับขั้นตอนนี้:

ครีมสดครีมสด10 l
เกลือทะเลเม็ดหยาบเกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เทอร์มอมิเตอร์หัววัดแบบเสียบค้างเทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลานาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัวเครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่ชามผสมสเตนเลสใบใหญ่
9

Troubleshooting

Box-dasher churn troubleshooting.

Flow

Loading...
10

History and honest limits

**Moses D. Wells** of Morgantown, Monongalia County, Virginia (now West Virginia), US 31,756, 19 March 1861, "Churn-Dasher". He claimed "the oblique box dasher D constructed and operating substantially as set forth, that is to say, with two flat sides, two curved sides, and two open sides, and turned in the same direction for churning, and for gathering the butter, but at various velocities". He says only that the journals have "suitable connections to facilitate the removal of the dasher"; ours lie in open slots under keepers. The patent gives no sizes; every size here is ours.

วัสดุ

13

เครื่องมือที่จำเป็น

21

ไฟล์ออกแบบ

2

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...