การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Reversible-Tip Soft-Face Hammer: Domed Rubber Tips Locked in Screw-On Sockets by an Internal Rib (West & Robinson, 1962)
Forge

สร้างโดย

Forge

13. พฤศจิกายน 2026NO
13
0
0
0
0

Reversible-Tip Soft-Face Hammer: Domed Rubber Tips Locked in Screw-On Sockets by an Internal Rib (West & Robinson, 1962)

Robert F. West and Walter H. Robinson of Connecticut received US 3,040,792, dated 26 June 1962, for The Stanley Works. A tubular socket screws onto a threaded boss at each end of the hammer's head. A rubber tip, domed at both ends, is pushed into the socket past an internal rib, which bites into it, and its rubber fills short grooves so it cannot turn. The tip can be pulled out and turned round to use its other end. On its first blows the tip's inner face squeezes into an off-centre hole in the boss and forms its own dowel, which stops the socket unscrewing. The patent gives no sizes; every size here is ours.
ขั้นสูง
About 2 days

คำแนะนำ

1

The tip's proportions

กำลังโหลดสมุด Jupyter…
2

Read US 3,040,792

"Upon being subjected to the percussive forces during initial use, some of the plastic material of the inner face 27 of the striking tip 26 will be extruded or forced into the eccentrically located recess 12 in the boss surface 10 to provide a self-forming dowel pin 28 which effectively prevents inadvertent loosening of the threaded connection between boss and mounting socket during use."
3

Turn the head 2

From 35 mm steel bar turn a body 4 80 mm long with a boss 8 20 mm across and 15 mm long at each end; cut M20 threads on the bosses with the die. In each boss's end face drill a recess 12 4 mm across and 4 mm deep, 6 mm off centre. Drill a 20 mm handle eye 6 through the middle in a V-block.

วัสดุสำหรับขั้นตอนนี้:

เหล็กเส้นกลมเหล็กกล้าละมุนเหล็กเส้นกลมเหล็กกล้าละมุน1 ชิ้น
น้ำมันตัดกลึงน้ำมันตัดกลึง1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
หัวจับกลึงสามจับหัวจับกลึงสามจับ
มีดกลึงมีดกลึง
มีดตัดงานกลึงมีดตัดงานกลึง
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
ด้ามจับดายเกลียวด้ามจับดายเกลียว
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
สว่านแท่นสว่านแท่น
วีบล็อกวีบล็อก
ชุดดอกสว่านชุดดอกสว่าน
เหล็กตอกนำศูนย์เหล็กตอกนำศูนย์
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
แว่นนิรภัยแว่นนิรภัย
4

Turn the sockets 14

From 48 mm bar turn two sockets 30 mm long. Knurl the outside 25. Drill and tap the collar end 18 M20, 8 mm deep. From the other end, before boring, drill four 4 mm holes 20 mm deep centred on a 38 mm circle, for the grooves 24. Bore the aperture 16 38 mm across and 20 mm deep, leaving a rib 22 4 mm wide 10 mm in, turned to 35 mm with 30 degree ramps either side.

วัสดุสำหรับขั้นตอนนี้:

เหล็กเส้นกลมเหล็กกล้าละมุนเหล็กเส้นกลมเหล็กกล้าละมุน2 ชิ้น
น้ำมันตัดกลึงน้ำมันตัดกลึง1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
หัวจับกลึงสามจับหัวจับกลึงสามจับ
มีดกลึงมีดกลึง
ก้านคว้านรูก้านคว้านรู
มีดตัดงานกลึงมีดตัดงานกลึง
เครื่องมือทำลาย (เนอร์ลิง)เครื่องมือทำลาย (เนอร์ลิง)
สว่านแท่นสว่านแท่น
ชุดดอกสว่านชุดดอกสว่าน
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
ด้ามจับต๊าปเกลียวด้ามจับต๊าปเกลียว
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
5

Make the tips 26

For each tip, cut nine discs of 4 mm natural rubber sheet 40 mm across and bond them into a stack with contact cement; clamp it overnight. Grind it round to 38.5 mm on the belt sander, then dome both ends: a large curve over most of the face and a small round where it meets the side, the same at both ends, 36 mm long overall.

วัสดุสำหรับขั้นตอนนี้:

แผ่นยางธรรมชาติแผ่นยางธรรมชาติ1 ชิ้น
กาวยางสัมผัสกาวยางสัมผัส1 ชิ้น

เครื่องมือที่ต้องใช้:

เข็มทิศเข็มทิศ
มีดคัตเตอร์งานประดิษฐ์มีดคัตเตอร์งานประดิษฐ์
แคลมป์แบบบาร์แคลมป์แบบบาร์
เครื่องขัดสายพานเครื่องขัดสายพาน
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
6

Assemble

Turn an ash handle to drive into the eye and wedge it. Screw a socket onto each boss hand-tight. Push a tip into each socket, squeezing it past the rib in the vice between soft packing, until its inner dome bears on the boss. Give the first few blows on a wood block: the rubber pushes into the boss's recess and locks the socket. To turn a tip round, pull it out, reverse it and push it back.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
กาวไม้กาวไม้1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงไม้เครื่องกลึงไม้
ชุดเครื่องมือกลึง (HSS)ชุดเครื่องมือกลึง (HSS)
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ค้อนหัวกลมค้อนหัวกลม
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
7

Troubleshooting

Reversible-tip hammer troubleshooting.

Flow

Loading...
8

History and honest limits

**Robert F. West** of Simsbury and **Walter H. Robinson** of West Hartford, Connecticut, assignors to The Stanley Works, US 3,040,792, dated 26 June 1962, filed 31 August 1960. They claimed sockets with an internal portion of reduced cross-section whose surfaces are "inclined to provide ramp surfaces", and symmetrical tips "having end surfaces of convexly curvilinear configuration", removable and "reversible in said sleeves". They list natural rubber, synthetic rubbers, nylon and cellulose esters for the tips; ours are laminated natural rubber. They give proportions but no sizes; every size here is ours.

วัสดุ

6

เครื่องมือที่จำเป็น

24

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...