การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)
Woody

สร้างโดย

Woody

4. พฤศจิกายน 2026NO
11
0
0
0
0

Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)

A small wooden wheelbarrow: ash hales (handles) framed with oak cross-pieces, splayed legs, a red-deal bottom and sides with a curved front board bound in hoop iron, and a 1 ft wheel of eight oak spokes and four ash felloes on an ash or oak axle. Painted red inside and light green outside, lined in a lighter colour and black. Source: P. N. Hasluck, Cassell's Cyclopaedia of Mechanics (1900), p. 176. Picture: the book's Figs. 1-2.
ระดับกลาง
Unknown

คำแนะนำ

1

Make the hales

Cut the two ash hales 3 ft 1 in long, 1 5/8 in deep by 1 1/2 in thick, the handles rising 3 3/4 in above the underside. Leave no more than 5/8 in on the faces of the hale tops; dress out 3/8 in on the face and 1/4 in underneath.

วัสดุสำหรับขั้นตอนนี้:

ไม้กระดานแอชไม้กระดานแอช1 hales 3 ft 1 in x 1 5/8 x 1 1/2 in

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
กบไสไม้กบไสไม้
กบสองมือจับกบสองมือจับ
2

Frame with oak cross-pieces

Make the cross-pieces of oak, edges dressed off underneath. Let the hind piece's tenons, gauged 1/2 in thick, come through the hales 1 1/4 in to support the legs (Fig. 2). Pin the hales and cross-pieces tight with 3/16 in wood pins.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้โอ๊กขาวแผ่นไม้โอ๊กขาว1 ชิ้น
เดือยไม้เดือยไม้1 3/16 in pins

เครื่องมือที่ต้องใช้:

เลื่อยสันแข็งเลื่อยสันแข็ง
สิ่วเจาะเดือยสิ่วเจาะเดือย
เกจขีดแนวเกจขีดแนว
สว่านมือหมุนพร้อมดอกสว่านมือหมุนพร้อมดอก
ฉากปรับมุมได้ฉากปรับมุมได้
3

Fit the legs and stays

Put on legs 1 1/2 in square, splayed at the top, standing 1 ft below the hales to suit a 1 ft wheel, with no more than a 1/4 in shoulder. Fasten legs to hales with 3 in bolts, heads outside. Fit four stays: two under the hales and two under the hind cross-pieces.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้โอ๊กขาวแผ่นไม้โอ๊กขาว1 legs 1 1/2 in square, stays
สลักเกลียวหัวกลมสลักเกลียวหัวกลม4 3 in

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
สว่านมือหมุนพร้อมดอกสว่านมือหมุนพร้อมดอก
ชุดไขควงชุดไขควง
4

Bottom and sides

Put in the bottom board of 1/2 in red deal, overhanging the front cross-piece 5/8 in; paint all joints. Fit the sides to the hales, the front leaning up to 3 3/4 in beyond square; sides 9 in deep by 5/8 in thick, reduced to 8 1/4 in at the hind ends, front ends edged. Run a 3/16 in or 1/4 in bead on the edge.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้สนแผ่นไม้สน1 1/2 in bottom, 5/8 in sides
สีน้ำมันสีน้ำมัน1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
กบไสไม้กบไสไม้
ชุดพู่กันชุดพู่กัน
5

Front board and ironwork

Fit the front board, of 3/4 in red deal or elm, on top of the hales and bottom board, rising in a curve 1 1/4 in above the sides. Paint the joints and nail the sides to it with 1 1/2 in cut nails; screw on the 7/8 in hoop iron with 3/4 in round-headed screws.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้สนแผ่นไม้สน1 3/4 in front board
ตะปูเหล็กตะปูเหล็ก1 1 1/2 in cut nails
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 7/8 in hoop iron
สกรูไม้สกรูไม้1 3/4 in round-headed
สีน้ำมันสีน้ำมัน1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
ค้อนค้อน
ชุดไขควงชุดไขควง
ชุดพู่กันชุดพู่กัน
6

Make the wheel

Turn an ash or oak axle 8 1/4 in long by 2 1/2 in, its ends turned down to 1 1/2 in for ferrules 1 in long; drive 3/8 in round pins into the ends to stand out 1 in. Fit eight oak spokes 3/4 in by 1/2 in and four ash felloes 1 1/4 in square, joined with four 1/4 in dowels and bevelled to take a 3/4 in by 1/8 in hoop, rounded inside.

วัสดุสำหรับขั้นตอนนี้:

ไม้กระดานแอชไม้กระดานแอช1 axle and felloes
แผ่นไม้โอ๊กขาวแผ่นไม้โอ๊กขาว1 spokes
เหล็กเส้นกลมเหล็กเส้นกลม1 3/8 in pins
เดือยไม้เดือยไม้4 1/4 in
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 3/4 x 1/8 in tyre

เครื่องมือที่ต้องใช้:

เครื่องกลึงไม้เครื่องกลึงไม้
กบสองมือจับกบสองมือจับ
สว่านมือหมุนพร้อมดอกสว่านมือหมุนพร้อมดอก
ค้อนค้อน
7

Hang the wheel and paint

Screw under each hale an iron 3/4 in broad by 1/8 in thick, long enough to pass the front cross-piece by 2 or 3 in, its eye taking the axle pin. Paint the wheel and the inside of the barrow red, the outside light green, lined in a lighter colour and black.

วัสดุสำหรับขั้นตอนนี้:

เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน2 3/4 x 1/8 in irons
สกรูไม้สกรูไม้1 ชิ้น
สีน้ำมันสีน้ำมัน1 ชิ้น

เครื่องมือที่ต้องใช้:

ชุดไขควงชุดไขควง
ชุดพู่กันชุดพู่กัน

วัสดุ

10

เครื่องมือที่จำเป็น

12

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...