การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Cam-Lock Drill-Press Vise: Holed Steel Bed, Pinned Jaws and an Eccentric Cam (Popular Mechanics, 1920)
C. H. Willey's quick-acting vise for the drill-press table (Popular Mechanics, 1920): a 1/2 x 3 in. steel bed drilled with 5/8 in. holes 7/8 in. apart and bolted down on slotted end pieces, a fixed jaw pinned into any hole, a sliding jaw kept on the bar by a riveted cross pin, and an eccentric cam on a handle that locks the work.
ระดับกลาง
A day
คำแนะนำ
1
1
The steps
The steps
กำลังโหลดสมุด Jupyter…
2
2
Read Willey
Read Willey
"A very efficient, quick-opening and closing vise for the drill-press table."
3
3
Make the bed
Make the bed
Cut a bed bar from 1/2 x 3 in. (13 x 76 mm) steel to suit your table (length ours). Drill a row of 5/8 in. (16 mm) holes 7/8 in. (22 mm) apart along its middle.
วัสดุสำหรับขั้นตอนนี้:
เหล็กแบนกล้าละมุน1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก
เหล็กตอกนำศูนย์
สว่านแท่น
ชุดดอกสว่าน4
4
Make the end supports
Make the end supports
Cut two short pieces of the same stock, slot them for bolts to the drill-press table and fix one under each end of the bed (ours: bolted), so the bed stands clear of the table.
วัสดุสำหรับขั้นตอนนี้:
เหล็กแบนกล้าละมุน1 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาด1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก
สว่านแท่น
ชุดดอกสว่าน
ตะไบ (ตะไบมือ)5
5
Make the fixed jaw
Make the fixed jaw
Cut out a steel block underneath so it straddles the bed (stock and size ours). Drive a pin into it, downward, that fits the 5/8 in. holes.
วัสดุสำหรับขั้นตอนนี้:
เหล็กแบนกล้าละมุน1 ชิ้น
แท่งเหล็กกลมคาร์บอนต่ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
สว่านแท่น
ชุดดอกสว่าน
ค้อนหัวกลม6
6
Make the sliding jaw
Make the sliding jaw
Cut a second block the same way. Pass a horizontal pin across the opening below the bed and rivet it to the jaw's sides, so the jaw slides along the bar but cannot lift off.
วัสดุสำหรับขั้นตอนนี้:
เหล็กแบนกล้าละมุน1 ชิ้น
แท่งเหล็กกลมคาร์บอนต่ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
สว่านแท่น
ชุดดอกสว่าน
ค้อนหัวกลม
ปากกาจับชิ้นงานหน้าโต๊ะ7
7
Make the cam
Make the cam
Saw a disk off steel shafting. Drive a pin that fits the 5/8 in. holes into one face, off centre. At right angles to it, drill a hole in the rim and fit a handle.
วัสดุสำหรับขั้นตอนนี้:
เพลาเหล็กกล้า1 ชิ้น
แท่งเหล็กกลมคาร์บอนต่ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก
สว่านแท่น
ชุดดอกสว่าน
ค้อนหัวกลม8
8
Use it
Use it
Bolt the bed to the table. Set the fixed jaw's pin in the hole that suits the work, slide the jaw up, drop the cam pin into the hole behind it and swing the handle to lock the work.
วัสดุสำหรับขั้นตอนนี้:
ชุดสลักเกลียวหกเหลี่ยมคละขนาด1 ชิ้นเครื่องมือที่ต้องใช้:
สว่านแท่น9
9
Troubleshooting
Troubleshooting
Drill vise troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
From C. H. Willey, "A Simple Drill Vise", **Popular Mechanics** vol. 34 (November 1920), p. 3340 (checked on the archive.org scan of Popular Mechanics Shop Notes, popularmechanic00unkngoog). He gives only the bed section and the hole size and spacing; jaw and cam sizes, the bar length, how the end pieces are fixed and the cam offset are ours.
วัสดุ
4- 1 ชิ้นตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้


