ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Valve-and-Cap Churn Dasher: Cream Driven Through Hinged Valves and Out of a Perforated Top Against a Sliding Cap
Buttercup

สร้างโดย

Buttercup

10. พฤศจิกายน 2026IE
8
0
0
0
0

Valve-and-Cap Churn Dasher: Cream Driven Through Hinged Valves and Out of a Perforated Top Against a Sliding Cap

Parker Wineman of Loydsville, Ohio, received US 24,898, dated 26 July 1859, for a churn dasher that is itself a closed vessel. Pushed down, it takes cream in under hinged valves on its sides; the cream mingles with the air inside and is driven out through the holes of its perforated top against a cap that slides on the shaft up to a stop. The butter falls to the bottom of the dasher, and a segment of it is taken out to remove the butter. This rung prints the dasher for a 20-litre bucket.
ระดับกลาง
About 1 day, plus printing

คำแนะนำ

1

Where the cream stands

กำลังโหลดสมุด Jupyter…
2

An up-and-down dasher, before it

Lake's dashers cut the cream with notched boards. Wineman's dasher takes the cream inside it and drives it out against a cap.
3

Read US 24,898

"As the dasher is forced downward, the cream is forced under the valves (d) into the dasher, where it instantly mingles with the contained air, and is forced through the perforations (i) of the top of the dasher (c) against the cap with such violence as to burst the particles of cream or milk in which the butter is contained."
4

Print the dasher body

The octagonal dasher B, 160 mm across flats and 190 mm tall, closed at the floor, with two ports, the hinge lugs, the hub for the shaft and the opening for the side panel. Print it standing on its floor. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
5

Print the perforated top c

The top c with 56 holes of 6 mm, a lip that drops into the body and a hub for the shaft. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
6

Print the valve flaps d

One flap, 50 x 100 mm with its hinge knuckle. Print two. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
7

Print the side panel

The removable segment, a panel with a flange that sits on a lip at its foot. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
8

Print the cap f

The cap, 168 mm across, a shallow cone with a 26 mm bore that slides on the shaft. PETG, 0.2 mm layers, 30 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
9

Shaft, pins and handle

Cut a 25 mm stainless tube 600 mm long for the shaft e. Drill 6 mm holes across it 10 mm and 185 mm from its foot for the pins that hold the body's hub and the top's hub, and one 233 mm from its foot for stop g. Cut 6 mm stainless pins 44 mm long and 3 mm pins 64 mm long, file their ends smooth, and make a hardwood T handle 200 mm wide bored for the tube's top.

วัสดุสำหรับขั้นตอนนี้:

ท่อสเตนเลสท่อสเตนเลส1 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส2 ชิ้น
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
กาวไม้กาวไม้1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
เลื่อยมือเลื่อยมือ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
กระดาษทรายกระดาษทราย
ตลับเมตรตลับเมตร
10

Assemble the dasher

Slide the body onto the shaft and pin its hub. Hang a flap over each port on a 3 mm pin through the lugs, and check it swings out freely and falls back shut. Press the top c into the body and pin its hub. Slide the cap f on above it and push the stop pin g through, so the cap can lift 20 mm. Set the side panel's foot on its lip and slide the 3 mm locking pin over its top. Put the handle on, and pass the shaft through a 28 mm hole in the bucket's lid.

วัสดุสำหรับขั้นตอนนี้:

เส้นใย PETGเส้นใย PETG1 ชิ้น
ถังขนาด 20 ลิตรถังขนาด 20 ลิตร1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
11

The build in 3D

FreeCAD model of this build, half the bucket and lid cut away: the octagonal dasher with its flaps swung open, the perforated top, the cap lifted to its stop, the shaft and handle. It was checked at three heights of the stroke with the flaps shut and open and the cap down and up.
ไฟล์แบบBLENDCC0 - Free
12

Churn

Pour about 8 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer, and put the lid on. Work the handle up and down about 100 mm, keeping the dasher's floor off the bucket's floor, and time it. When the butter has come, lift the dasher out, pull the panel's pin, take out the panel and scoop out the butter. Pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

วัสดุสำหรับขั้นตอนนี้:

ครีมสดครีมสด8 l
เกลือทะเลเม็ดหยาบเกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เทอร์มอมิเตอร์หัววัดแบบเสียบค้างเทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลานาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัวเครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่ชามผสมสเตนเลสใบใหญ่
13

Troubleshooting

Valve-and-cap dasher troubleshooting.

Flow

Loading...
14

History and honest limits

**Parker Wineman** of Loydsville, Belmont County, Ohio, US 24,898, 26 July 1859, "Churn-Dasher". He claimed the dasher with its perforated top, movable cap and hinged valves. He gives no sizes and says the valves may be arranged in various ways. Fig. 1 draws the dasher with flat sides, which we copy; our flaps hang over ports near the top as in Fig. 2. Every size is ours, and our printed build has not been churned with.

วัสดุ

9

เครื่องมือที่จำเป็น

13

ไฟล์ออกแบบ

6

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...