ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Wire-Arc Spray Gun: Two Crossed Wires, a Vibrating Arc and an Air Blast (Schoop, US 1,133,508, 1915)
Forge

สร้างโดย

Forge

3. พฤศจิกายน 2026NO
13
0
0
0
0

Wire-Arc Spray Gun: Two Crossed Wires, a Vibrating Arc and an Air Blast (Schoop, US 1,133,508, 1915)

The first wire-arc metal sprayer. Two metal wires are pushed through iron tubes until their tips cross. Current through the wires also runs an electromagnet that pulls one tube back, so a small arc springs between the tips and melts them; a jet of air blows the molten metal off as a fine spray and puts the arc out, the magnet lets go, the wires touch again, and the cycle repeats very fast. Result: a continuous spray of molten metal for coating a surface. Source: M. U. Schoop, US 1,133,508 (1915). Unknown: the wire metals and sizes, the coil, the air pressure. Picture: the patent drawing.
ขั้นสูง
Unknown

คำแนะนำ

1

Make the feed tubes and rolls

Make two feed tubes ending in nozzles, preferably of iron. For each, mount a pair of feed rolls in a frame to push a wire through the tube. Set the tubes at about 90° to each other so the wires cross as they come out, the nozzles only a few millimetres apart. Mount one tube on an elastic support so it can move a little. Not given: sizes, the roll drive (the air blast may drive a small turbine for it).

วัสดุสำหรับขั้นตอนนี้:

ท่อเหล็กท่อเหล็ก2 feed tubes
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 rolls, frames
แหนบซ้อนแผ่นแหนบซ้อนแผ่น1 elastic support

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
2

Fit the electromagnet

Wind an electromagnet beside the springing tube, so the tube is its armature. Wire the coil into the same circuit as the two tubes and wires, positive to one tube and negative to the other. When current flows the magnet pulls the tube aside and draws its wire slightly back from the other. Ours: enamelled copper wire for the coil. Not given: the coil.

วัสดุสำหรับขั้นตอนนี้:

ลวดทองแดงอาบน้ำยาลวดทองแดงอาบน้ำยา1 coil
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 magnet core
ลวดทองแดงลวดทองแดง1 circuit leads

เครื่องมือที่ต้องใช้:

ชุดไขควงชุดไขควง
3

Fit the air blast

Aim a blast pipe at the point where the wires cross, either close to it or 20-30 mm away, whichever sprays best for the metal. Feed it with compressed air or another gas. Not given: the pressure.

วัสดุสำหรับขั้นตอนนี้:

หัวฉีดลมหัวฉีดลม1 ชิ้น
สายลมสายลม1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องอัดอากาศอุตสาหกรรมเครื่องอัดอากาศอุตสาหกรรม
ประแจเลื่อนประแจเลื่อน
4

Spray

Load a wire of the coating metal in each tube and feed them until they touch. Switch on the current, generally 40 to 75 volts depending on the metal and wire thickness, and the air. The magnet pulls the wires apart, an arc melts their tips, the air blows the melt away as spray and snuffs the arc, the magnet releases, and the cycle repeats very rapidly. The positive wire burns faster, so feed it faster or use a thicker wire; match the feed to the melting. Hold the work in the spray. Without the vibration the arc flickers and the wires may weld together.

เครื่องมือที่ต้องใช้:

แหล่งจ่ายไฟกระแสตรงแหล่งจ่ายไฟกระแสตรง
เครื่องอัดอากาศอุตสาหกรรมเครื่องอัดอากาศอุตสาหกรรม
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ

วัสดุ

7

เครื่องมือที่จำเป็น

7

วัสดุจากพิมพ์เขียวที่เชื่อมต่อ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...