ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Interlapping Spiral-Dasher Churn: Two Upright Shafts With Arms Set in Screw Form Interlap, One Turning the Other
Buttercup

สร้างโดย

Buttercup

11. พฤศจิกายน 2026IE
7
0
0
0
0

Interlapping Spiral-Dasher Churn: Two Upright Shafts With Arms Set in Screw Form Interlap, One Turning the Other

D. M. Woodin of Brandon, Wisconsin, received US 28,528, dated 29 May 1860, for a churn. Two shafts stand side by side in a box, each with arms set round it in a screw form; the arms of one pass between the arms of the other, so turning one shaft with the crank turns the second "like spiral gearing". The two screws force the cream down between them and it rises again outside, while the arms meet and close on each other, breaking the globules. The patent gives no sizes; every size here is ours.
ระดับกลาง
About 2 days, plus printing

คำแนะนำ

1

Where the shafts go

กำลังโหลดสมุด Jupyter…
2

Two dashers turning contrary ways, three months before

Vaughan joins his two dashers with pinions. Woodin lets the dashers' own arms drive one another.
3

Read US 28,528

"These two spiral wheels revolving in this way force the cream downward all the while, but it rising again on the outside of the wheels, is kept moving in a constant current from top to bottom, and from bottom to top. In addition to the friction thus caused and the moving of the cream in a constant current, the arms overlapping and interlapping mash the globules of the cream as they meet and press against each other."
4

Print the crown wheel

Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
5

Print the pinion

Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
6

Box A and steps

From 20 mm hardwood board make a box 350 x 220 mm inside and 350 deep; glue and screw it and seal the inside joints with silicone sealant. Screw two hardwood blocks 50 x 50 x 10 mm to the floor on the long centre line, 128 mm apart, the first 110 mm from one end, each bored 16.6 mm, 6 deep, as steps. Cut a lid to sit on top, bored 17 mm over each step.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง3 ชิ้น
ท่อนไม้เนื้อแข็งท่อนไม้เนื้อแข็ง2 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สกรูไม้สกรูไม้40 ชิ้น
ซิลิโคนยาแนวซิลิโคนยาแนว1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
แคลมป์แบบบาร์แคลมป์แบบบาร์
ชุดไขควงชุดไขควง
ตลับเมตรตลับเมตร
7

Wheels B, B with spiral arms a

For each wheel cut fourteen hardwood bars 190 x 30 x 20 mm and halve them together in pairs into seven crosses, each bored 16.2 mm at the crossing. Thread the crosses onto a 16 mm stainless shaft, 40 mm apart centre to centre from 40 mm above the floor, each turned 22.5 degrees from the one below, checked with the protractor, and pin each through. Turn the second wheel's crosses the opposite way, so its spiral is of the other hand. The driven shaft is 425 mm long, the other 375.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง2 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส2 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สลักผ่าสลักผ่า14 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
ชุดสิ่วไม้ชุดสิ่วไม้
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
ไม้โปรแทรกเตอร์ไม้โปรแทรกเตอร์
กระดาษทรายกระดาษทราย
8

Set the wheels and the gearing

Stand both shafts in their steps and turn the second so its arms sit 45 degrees between the first's at every level; they must pass each other about 5 mm apart all the way round. Put on the lid. On the driven shaft's top fit the pinion; on the lid screw two hardwood chairs carrying a 12 mm stainless crank shaft with the crown wheel meshing it, and a hardwood crank with a dowel handle. Hold the shafts with collars.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สกรูไม้สกรูไม้8 ชิ้น
Shaft CollarShaft Collar4 ชิ้น
เส้นใย PETGเส้นใย PETG1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ชุดไขควงชุดไขควง
9

The build in 3D

FreeCAD model of this build, one side left off: the two wheels with their seven crossed stations turned in spirals of opposite hand, their arms interlapping, the steps, the lid and the crank with crown wheel and pinion on the driven shaft.
ไฟล์แบบBLENDCC0 - Free
10

Churn

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the box, put the lid and gearing on, and turn the crank steadily, timing it, the way that drives the cream down between the wheels. When the butter comes, lift off the lid and the wheels, take out the butter, tip the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

วัสดุสำหรับขั้นตอนนี้:

ครีมสดครีมสด10 l
เกลือทะเลเม็ดหยาบเกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เทอร์มอมิเตอร์หัววัดแบบเสียบค้างเทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลานาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัวเครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่ชามผสมสเตนเลสใบใหญ่
11

Troubleshooting

Interlapping-dasher churn troubleshooting.

Flow

Loading...
12

History and honest limits

**D. M. Woodin** of Brandon, Fond du Lac County, Wisconsin, US 28,528, 29 May 1860, "Churn". He claimed the two dasher shafts with wings in screw form, one turned by the other. He does not give the number of arms or how far each turns on; our seven stations of four arms, 22.5 degrees apart, and the spacing are ours, as are the printed crown wheel and pinion that stand in for his bevel wheels.

วัสดุ

13

เครื่องมือที่จำเป็น

17

ไฟล์ออกแบบ

3

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...