การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Workbench: a Pine Bench with a Laminated Maple Top and Vise (Boy Mechanic, 1913)
Woody

สร้างโดย

Woody

4. พฤศจิกายน 2026NO
8
0
0
0
0

Workbench: a Pine Bench with a Laminated Maple Top and Vise (Boy Mechanic, 1913)

The same pine bench with a harder top: 14 maple strips set on edge, glued and screwed together, with a back board, a tool rack and a wooden vise on an iron bench screw. Source: C. E. McKinney, Jr., 'Homemade Workbench', The Boy Mechanic, Book 1 (1913), pp. 442-443. Picture: Figs. 1-3 of the book.
ระดับกลาง
Unknown

คำแนะนำ

1

Make the two leg frames

Cut four 2 x 4 in pine legs 23 in long with a tenon on each end 1/2 in thick, 3 1/2 in wide and 1 1/2 in long (Fig. 1, A and B). Cut four crosspieces of the same stock 20 in long, mortised in the narrow edge 1 1/4 in from each end, and slope their corners from the leg out to the middle. Fit each pair of legs to a pair of crosspieces to make the two supports.

วัสดุสำหรับขั้นตอนนี้:

ไม้สนแปรรูปไม้สนแปรรูป1 2 x 4 in: legs, crosspieces

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
สิ่วเจาะเดือยสิ่วเจาะเดือย
ค้อนค้อน
2

Brace them together

Join the supports with two 2 x 4 in braces 24 in long, ends sawn square. Bore through each leg and 4 in into the centre of each brace end, bore an intersecting hole on the back of each brace for the nut, and draw each joint tight with a 3/8 x 6 in bolt (Fig. 2, J). A cross brace on the back stops rocking when planing.

วัสดุสำหรับขั้นตอนนี้:

ไม้สนแปรรูปไม้สนแปรรูป1 2 x 4 in: braces
สลักเกลียวหัวกลมสลักเกลียวหัวกลม4 3/8 x 6 in

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
สว่านมือหมุนพร้อมดอกสว่านมือหมุนพร้อมดอก
ประแจเลื่อนประแจเลื่อน
3

Build up the maple top

Make the main top M of 14 maple strips 7/8 in thick, 2 in wide and 3 1/2 ft long, set on edge, each glued and screwed to the next, all with the grain one way so it planes smooth. Rabbet its back edge 1/2 in to take a back board N of the same length, 8 1/2 in wide and 7/8 in thick. Screw the top to the top crosspieces with long screws.

วัสดุสำหรับขั้นตอนนี้:

วัสดุที่ไม่ทราบวัสดุที่ไม่ทราบ14 maple strips 7/8 x 2 in x 3 1/2 ft
กาวไม้กาวไม้1 ชิ้น
แผ่นไม้สนแผ่นไม้สน1 back board
สกรูไม้สกรูไม้1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
กบมือเล็กกบมือเล็ก
ไขควงปากแบนไขควงปากแบน
4

Add the tool rack

Nail a board E 10 in wide to the back of the bench and fasten a 2 1/2 in board F on top of it at right angles; both 7/8 in thick and 3 1/2 ft long. Bore holes or cut notches in F to hold tools.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้สนแผ่นไม้สน2 7/8 in, 3 1/2 ft
ตะปูตะปู1 ชิ้น

เครื่องมือที่ต้องใช้:

สว่านมือหมุนพร้อมดอกสว่านมือหมุนพร้อมดอก
เลื่อยมือเลื่อยมือ
ค้อนค้อน
5

Fit the vise

Fasten an iron bench screw in a 2 x 6 in block 12 in long. Mortise two guide rails 7/8 x 1 1/2 in and 20 in long into the block; they slide in mortises in a 2 x 4 piece L bolted under the top, which holds the bench-screw nut between the two mortises. Nail L to a top crosspiece and to a 2 x 4 piece P bolted under the top at the end (Fig. 3).

วัสดุสำหรับขั้นตอนนี้:

ไม้สนแปรรูปไม้สนแปรรูป1 2 x 6 block, 2 x 4 pieces, guide rails
สกรูโต๊ะช่างสำหรับงานแกะไม้สกรูโต๊ะช่างสำหรับงานแกะไม้1 ชิ้น
สลักเกลียวหัวกลมสลักเกลียวหัวกลม1 for L and P
ตะปูตะปู1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
สิ่วเจาะเดือยสิ่วเจาะเดือย
สว่านมือหมุนพร้อมดอกสว่านมือหมุนพร้อมดอก
ประแจเลื่อนประแจเลื่อน
ค้อนค้อน

วัสดุ

8

เครื่องมือที่จำเป็น

7

พิมพ์เขียวนี้สร้าง

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...