ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Rotary-Tub Spout Churn: A Friction Wheel Spins the Tub, a Fixed Spout Catches the Climbing Cream and Jets It Into a Basket
Clark Wright and William Phelps of Sycamore, Illinois, received US 28,802, dated 19 June 1860, for a churn. The tub itself spins, carried on a plate that rests on a crank-turned friction wheel. The cream climbs the side until a flange stops it, where a fixed spout catches it and shoots it into a perforated basket hung loose in the middle; the butter collects in the basket while the milk runs out through its holes and climbs again.
The patent gives no sizes; every size here is ours.
ขั้นสูง
About 2 days, plus printing
คำแนะนำ
1
1
How fast the tub must turn for the cream to climb
How fast the tub must turn for the cream to climb
กำลังโหลดสมุด Jupyter…
2
2
Cream flung outward and jetted, three months before
Cream flung outward and jetted, three months before
Sangster spins paddles to fling the cream. Wright and Phelps spin the whole tub.
3
3
Read US 28,802
Read US 28,802
"A quantity of cream being placed in the tub F, and the latter rapidly rotated by means of the crank D and friction wheel E, the cream ascends the sides of the tub by centrifugal force until arrested by the flange f and being caught by the spout K is deflected inward and projected in a forcible and continuous stream into the basket H, causing violent agitation in the body of cream as well as friction as it flows out through the apertures in the basket."
4
4
Print the basket H
Print the basket H
Perforated cone basket 160 mm across at the top, 130 at the bottom, 150 tall, with a hub bored 12.6 mm. PETG, 0.2 mm layers, 30 % infill, 4 walls.
5
5
Print the spout K
Print the spout K
Curved spout 40 mm wide, its mouth at the wall turning inward over 55 mm, with a hanger and a clamp that slides along the bar I. PETG, 0.2 mm layers, 30 % infill, 4 walls.
6
6
Base A, standard B, spindle G and plate g
Base A, standard B, spindle G and plate g
Make a hardwood base 520 x 560 mm. Screw a hardwood standard 60 mm square in its middle, its top bored 16.6 mm to take a 16 mm stainless spindle. Cut a plywood disk plate 300 mm across, fix the spindle in its centre, and screw the bucket down on it, sealing the screw heads inside with silicone. Screw a ring of HDPE sheet, 26 mm wide, inside the bucket 340 mm up as the flange f, and a hardwood socket bored 12.6 mm in the floor's centre.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง2 ชิ้น
แผ่นไม้อัด1 ชิ้น
แท่งสเตนเลส1 ชิ้น
ถังขนาด 20 ลิตร1 ชิ้น
แผ่น HDPE1 ชิ้น
ท่อนไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้16 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
เลื่อยจิ๊กซอว์
สว่านไร้สาย
ชุดดอกสว่าน
ชุดดอกสว่านใบพาย
แคลมป์แบบบาร์
ชุดไขควง7
7
Friction wheel E, shaft C and crank D
Friction wheel E, shaft C and crank D
Turn a hardwood wheel E 220 mm across with its rim rounded in section, as the patent's "regular convexity". Bolt two hardwood bearing blocks to the base so a 16 mm stainless shaft C runs straight out from under the spindle, at a height where the wheel, fixed on its inner end 50 mm from the spindle, just carries the plate. The shaft must point at the spindle, so the wheel rolls on the plate without scrubbing. Fix the wheel on the shaft, and a hardwood crank D with a dowel handle on its end; hold it with collars.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
แท่งสเตนเลส1 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
สลักเกลียวหัวกลม4 ชิ้น
น็อตปีกผีเสื้อ4 ชิ้น
Shaft Collar2 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องกลึงไม้
กระดาษทราย
สว่านไร้สาย
ชุดดอกสว่าน
เลื่อยตัดเหล็ก
ประแจเลื่อน8
8
Standards J, bar I, pin, basket H and spout K
Standards J, bar I, pin, basket H and spout K
Stand two hardwood standards J 30 x 30 mm either side of the bucket and join their tops with a bar I across it, bored 12.6 mm over the centre. Drop a 12 mm stainless pin through the bar into the floor socket and slide the basket onto it so it turns freely. Clip the spout's clamp on the bar so its mouth sits just under the flange, close to the wall, facing against the tub's turn; slide it in or out to suit.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
แท่งสเตนเลส1 ชิ้น
สกรูไม้6 ชิ้น
กาวไม้1 ชิ้น
เส้นใย PETG1 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สาย
ชุดดอกสว่าน
เลื่อยตัดเหล็ก
ตลับเมตร9
9
The build in 3D
The build in 3D
FreeCAD model of this build, the tub cut open: the spindle and plate on the friction wheel and crank, the flange, the basket on its pin, the spout hanging from the bar, and the standards.
10
10
Churn
Churn
Pour about 5 litres of heavy cream at about 15 °C, checked with the thermometer, into the tub around the basket. Turn the crank briskly, timing it, until the cream climbs to the flange and runs from the spout into the basket. Keep on until the butter has gathered in the basket. Lift out the pin and basket with the butter, pour off the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด5 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่11
11
Troubleshooting
Troubleshooting
Rotary-tub churn troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Clark Wright** and **William Phelps** of Sycamore, DeKalb County, Illinois, US 28,802, 19 June 1860, "Churn". They claimed the rotary tub, stationary spout and basket together. Their wheel and plate meet as two crossed discs, the wheel's rounded rim avoiding both side thrust and broad rubbing faces. Every size here is ours.
วัสดุ
17- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- 22 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 5 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
17- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
3พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

False-Bottom Jet Churn: Paddles Under a Pierced Partition Draw Cream Down at the Centre and Jet It Up at the Rim
โดย Buttercup
งานไม้
13
0
0
0
0
0

Roller-and-Concave Churn: Cream Falls Between a Turning Roller and an Adjustable Concave, Then Onto a Dasher Below
โดย Buttercup
งานไม้
7
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
โดย TheChef
งานฝีมือ
63
0
0
0
0
0
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

