İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Great Bellows of the Smelting Works: Pine Boards, Linden Bows, Ox-Hide and Iron Nozzle (Agricola, 1556)
Forge

Oluşturan

Forge

14. Kasım 2026NO
11
0
0
0
0

Great Bellows of the Smelting Works: Pine Boards, Linden Bows, Ox-Hide and Iron Nozzle (Agricola, 1556)

The large blast bellows of a 16th-century smelting works, every part measured, from Agricola's De Re Metallica, Book IX (1556): two tapered boards of glued pine edged with linden, about 1.7 m long, two linden bows, two ox-hides nailed on with T-headed nails, a goatskin flap valve in the lower board, and a glued head carrying a 3 ft iron nozzle.
İleri
About 2 weeks

Talimatlar

1

Roman units in metric

Jupyter defteri yükleniyor…
2

Read De Re Metallica, Book IX

"Each bellows consists of a body and a head. The body is composed of two 'boards', two bows, and two hides."
3

Make the upper board

Glue two pieces of pine into a board a palm thick, 5 ft 3 palms long, 2-1/2 ft wide at the back (sides a little curved) and a cubit wide at the front, tapering to the head. Glue on linden edge strips, 7 digits wide at the back and 1-1/2 at the front, to take the nails. Cut an aperture 6 by 4 digits in the middle, 1 ft 3 palms from the head, with a sliding lid 2 palms 1 digit square and 3 digits thick running in mouldings a palm wide and 3 digits thick (or bore 2-3 round holes with plugs). Glue and peg a handle 7 palms or longer (2 palms wide, 1 thick on the board; rounded and 7 digits thick beyond), with a 2 ft cleat 2 palms wide and a palm thick over it and another 2 ft cleat underneath, 3 palms from the end.

Bu adım için malzemeler:

Çam tahtaÇam tahta2 adet
Ihlamur LevhaIhlamur Levha1 adet
Deri tutkalıDeri tutkalı1 adet
Ahşap Kavela ÇubuğuAhşap Kavela Çubuğu1 adet

Gerekli aletler:

El TesteresiEl Testeresi
El rendesiEl rendesi
Marangoz keskileriMarangoz keskileri
Kol matkabı ve ucuKol matkabı ve ucu
Çubuklu işkenceÇubuklu işkence
4

Make the lower board and flap valve

Make the lower board the same way and a cubit longer (the extra length is part of the head). About a cubit from the back, centred, cut an air-hole a foot long and 3 palms wide, leaving a rib a palm long and 1/3 digit wide across it. Make the flap a foot 3 digits by 3 palms 3 digits of thin board covered with goatskin, hair toward the ground, hinged with a doubled strip of leather a palm wide nailed to it and tied through two holes 7 digits apart. A foot beyond, fix a slightly elliptical iron ring 2 palms by 1 on a staple, 3 palms from the back, for the wooden bolt that holds the board to its frame (or use two iron screws).

Bu adım için malzemeler:

Çam tahtaÇam tahta2 adet
Ihlamur LevhaIhlamur Levha1 adet
Deri tutkalıDeri tutkalı1 adet
Ham keçi derisiHam keçi derisi1 adet
Deri şeritDeri şerit1 adet
Metal halkaMetal halka1 adet
ÇivilerÇiviler1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Marangoz keskileriMarangoz keskileri
Kol matkabı ve ucuKol matkabı ve ucu
ÇekiçÇekiç
5

Make the bows

Make each bow as long as the upper board from four pieces of linden 3 digits thick: two long pieces 7 digits wide at the back and 2-1/2 at the front, a back piece 2 palms wide, its ends a little over a digit thick, bent to meet the long pieces, mortised, bored and pegged with glued pegs. Mortise in a crossbar a cubit from the head, a foot long without tenons and a palm 2 digits wide. Glue and peg two small pieces, 3 palms 2 digits long, a palm high and a digit thick, at the head to keep the bow ends off the air passage.

Bu adım için malzemeler:

Ihlamur LevhaIhlamur Levha2 adet
Deri tutkalıDeri tutkalı1 adet
Ahşap Kavela ÇubuğuAhşap Kavela Çubuğu1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Marangoz keskileriMarangoz keskileri
Kol matkabı ve ucuKol matkabı ve ucu
Ahşap TokmakAhşap Tokmak
6

Make the head and nozzle

Glue the upper head board, a cubit long and 1-1/2 palms thick, onto the lower board's extension (a palm and a digit thick). Shape it a cubit wide at the back, 2 digits narrower 3 palms forward, then round the front to 2 palms 2 digits across and bind it with an iron ring 3 digits wide. Bore it for the nozzle: a pipe of thin iron plate 3 ft long, 3 digits across in front and a palm high by 2 palms wide at the back.

Bu adım için malzemeler:

Çam tahtaÇam tahta1 adet
Deri tutkalıDeri tutkalı1 adet
Demir levha (dövülmüş)Demir levha (dövülmüş)1 adet
Metal halkaMetal halka1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Kol matkabı ve ucuKol matkabı ve ucu
Demirci OcağıDemirci Ocağı
ÖrsÖrs
ÇekiçÇekiç
7

Hide the bellows

Use ox-hide (far better than horse), two hides each 3-1/2 ft wide at the back. Lay a long leather thong along each board and bow and nail the hide through it with T-shaped iron nails 5 digits long, horns 2-1/2 digits long and half a digit wide, the horn of one nail almost touching the next along the boards; on each bow two nails in the back piece and four in each long piece, ten in all. Pine strips nailed over the hide on the long pieces guard against tearing; iron screws through strips over the hide hold even better.

Bu adım için malzemeler:

Bitkisel tabaklanmış deriBitkisel tabaklanmış deri2 adet
Deri şeritDeri şerit1 adet
ÇivilerÇiviler1 adet

Gerekli aletler:

ÇekiçÇekiç
Deri bıçağıDeri bıçağı
MakasMakas
8

Troubleshooting

Bellows troubleshooting.

Flow

Loading...
9

History and honest limits

From Georgius Agricola, **De Re Metallica** (1556), Book IX, translated by Herbert C. and Lou H. Hoover, 1912 (checked on the archive.org scan georgiusagricola00agri, pp. 362-365). The frame and the machinery that work the bellows are not covered here. The metric conversions (digit ~1.85 cm, palm ~7.4 cm, Roman foot ~29.6 cm, cubit ~44.4 cm) and the tools are ours.

Malzemeler

10

Gerekli Aletler

11

Bu planla yapılan

İlgili Blueprint'ler

Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...