SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Bell-Crank Vibrating Beater Churn: Beaters Rocked on Hung Fulcrums by a Cranked Shaft
Rhodes improved "the common churn" by the way he worked and hung its beaters.
Clarkson Rhodes of Morrow, Ohio, received US 8,959, dated 18 May 1852, for a churn box whose top has a convex recess for the cranks to pass, ventilated by a perforated tin plate over a hole "some 3/4 or an inch in diameter." A shaft bent into a double bell crank turns across the top; rods from the shaft carry the fulcrum on which the beaters vibrate, and rods from the cranks give them "an alternate up and down motion." The internal work lifts out with the top for cleaning.
This rung works out the beaters' swing, then prints the beaters and fulcrum hangers, bends the cranked shaft, and makes butter.
Orta
About 4 hours, plus printing
Talimatlar
1
1
The beaters' swing
The beaters' swing
Jupyter defteri yükleniyor…
2
2
A double crank working the beaters before it
A double crank working the beaters before it
The embedded blueprint swings an upright dasher from a double crank. Rhodes rocks beaters on fulcrums hung from the cranked shaft itself.
3
3
Read US 8,959
Read US 8,959
"The shaft 1, 1, is turned by crank c, of which works the cranks 5, 5, and rods 3, 3, 3, 3 which gives the beaters or dashers 4, 4, 4, 4, an alternate up and down motion, and thereby causing an effectual churning of the milk."
4
4
Print the parts
Print the parts
Print four beaters (/uploads/blueprints/bell-crank-vibrating-beater-churn-beater.stl) and two fulcrum hangers (/uploads/blueprints/bell-crank-vibrating-beater-churn-fulcrum-hanger.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Bu adım için malzemeler:
PETG filament1 adetGerekli aletler:
FDM 3B yazıcı5
5
The cranked shaft
The cranked shaft
Bend a 6 mm steel rod into a shaft with two cranks of about 25 mm throw, pointing opposite ways, and a handle at one end. Lay it in notches in the ends of a food-safe box about 230 × 150 × 200 mm, under a plywood lid with a raised recess for the cranks and a small hole covered with perforated stainless sheet for air.
Bu adım için malzemeler:
Yumuşak Çelik Çubuk1 adet
Gıda sınıfı saklama kabı1 adet
Kontrplak levha1 adet
Paslanmaz çelik levha - 3041 adetGerekli aletler:
Kurbağacık anahtar
Demir Testeresi
Kıl Testere
Sac makası6
6
Hang the beaters
Hang the beaters
Hang each fulcrum hanger from the shaft beside a crank, on a loop of steel wire, and pin two beaters crossed on each hanger's lower hole. Join each beater's end to the nearer crank with a wire rod, eyes at both ends.
Bu adım için malzemeler:
Yay çeliği tel1 adet
Makine vidaları1 adet
Altıgen Somun1 adetGerekli aletler:
Kurbağacık anahtar
Tornavida takımı7
7
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: the box with one side off to show the cranked shaft across the top, the rods hanging to the fulcrums, the crossed beaters and the crank rods.
8
8
Crank and make butter
Crank and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 2 litres. Fit the lid and turn the handle steadily; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Bu adım için malzemeler:
Yağlı krema2000 ml
İri Deniz Tuzu1 adet
Su1 adetGerekli aletler:
Takılı kalan problu termometre
Kronometre
Dijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesi9
9
Beaters that jam, rods that bend
Beaters that jam, rods that bend
Bell-crank beater troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Clarkson Rhodes** of Morrow, Warren County, Ohio, received US 8,959, dated 18 May 1852 (the drawing sheet is lettered "G. Rhodes"; the specification gives Clarkson). He did not confine himself to the number or form of the dashers. He claimed the beaters hung by rods from the shaft on a fulcrum and worked by the rods and bell cranks.
**Honest limits.** A food-safe box, steel rod and printed beaters stand in for his. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
Malzemeler
11- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- Yer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 2000 mlYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
10- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
1İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler
Oscillating Paddle Churn: Oblique Paddles Swung to and Fro by a Strap
Martin tarafından
YİYECEK & İÇECEK
13
0
0
0
0
0
Spring-Wire Twin Dash Churn: Two Hinged Dashes Rocked by a Sprung Wire on a Crank
YourGrandma tarafından
YİYECEK & İÇECEK
8
0
0
0
0
0
Interraking Plunger Churn: Two Rakes Worked Oppositely by a Double Crank
Martin tarafından
YİYECEK & İÇECEK
5
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.