İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)
Woody

Oluşturan

Woody

4. Kasım 2026NO
12
0
0
0
0

Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)

A shop belt sander for dressing wood surfaces: a 6 in garnet-paper belt running over four crowned wooden pulleys, one driven by the lathe, pressed down onto the work with a hand float. Best belt speed about 2,500 ft per minute; leave about 1 in between work and belt. Source: Popular Mechanics Shop Notes for 1919, p. 3235. Picture: the article's drawing.
Orta
Unknown

Talimatlar

1

Turn the pulleys

Build up four solid wood pulleys 10 in across with 8 in faces and turn them in the lathe with a very slight crown; too much crown harms the belt.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası4 built-up pulleys

Gerekli aletler:

Ahşap torna tezgâhıAhşap torna tezgâhı
2

Mount the pulleys

Mount one pulley on a firmly held arbor in the lathe and the other three on iron-pipe shafts on a frame (drawing). Turn and file a true journal on each pipe, pour babbitt bushings in the pulleys, and cut oil grooves in the pipe or babbitt. Supporting the shafts on one side lets the belt slip off; supporting both sides is stronger.

Bu adım için malzemeler:

Çelik boru (kalın cidarlı, dişli uçlu)Çelik boru (kalın cidarlı, dişli uçlu)3 shafts
Bilinmeyen metalBilinmeyen metal1 babbitt bushings
Çam keresteÇam kereste1 frame

Gerekli aletler:

Metal EğeMetal Eğe
Delikli kevgirDelikli kevgir
El TesteresiEl Testeresi
ÇekiçÇekiç
3

Make the belt

Cut 6 in garnet paper (No. 1 1/2 for general work) so the ends just meet over the pulleys. Glue the smooth side at the joint, splice it with a strip of cloth about 1 in wide and then one about 3 in wide, cover each side with paper, and clamp between two small boards.

Bu adım için malzemeler:

Zımpara KağıdıZımpara Kağıdı1 6 in garnet paper
Pamuklu BezPamuklu Bez1 adet
Hayvansal tutkalHayvansal tutkal1 adet

Gerekli aletler:

C işkenceC işkence
4

Set up and run

Run the belt at about 2,500 ft per minute using the lathe's cone pulley. Set the work about 1 in below the belt on a table or a low sliding platform (two sets of tongue-and-groove joints at right angles), start the machine and press the belt down with a float like a blackboard eraser, or a roller.

Bu adım için malzemeler:

Çam keresteÇam kereste1 platform, float

Gerekli aletler:

Ahşap torna tezgâhıAhşap torna tezgâhı

Malzemeler

7

Gerekli Aletler

6

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...