İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Bench Glassblowing Torch: Brass Gas Blowpipe with a Glass Air Jet (Shenstone, 1916)
A glassblower's gas blowpipe you can make yourself: a brass tube with a side tube for gas, and a glass air jet down its middle fed from a foot-blower. A fine jet gives the small pointed flame for joints, and a wider jet the big brush flame for heating large tubes. It is pegged into a wooden block on a sheet-iron-covered bench, with taps for gas and air at the bench edge.
Result: a bench blowpipe for working glass tube. Make two: one about 11 mm bore for small work, one 15 to 17 mm for large.
Source: W. A. Shenstone, The Methods of Glass-Blowing (1916), pp. 3-9. Unknown: the brazing metal and the tap type. Picture: Fig. 1 of the book.
Orta
Unknown
Talimatlar
1
1
Braze the gas inlet
Braze the gas inlet
Take a brass tube for the body: about 11 mm bore for the small blowpipe, 15 to 17 mm for the large one. Braze a side tube for the gas onto it 10 to 12 cm from the back end, according to the tube's size. Fix a spike to it for mounting. Ours: borax as the flux. Not given: the brazing metal.
Bu adım için malzemeler:
Pirinç boru1 body and side tube
Bilinmeyen metal1 brazing metal and spike
Boraks tozu1 brazing fluxGerekli aletler:
Demir Testeresi
Demirci Ocağı2
2
Fit the glass air jet
Fit the glass air jet
Fit a glass tube down the middle of the brass tube, held by a cork at the back end, its tip near the mouth. For the small pointed flame, draw the tip down to the size of a large knitting needle. For a large flame rich in air, the tip may be nearly half the bore of the brass tube. Make several air tubes of different sizes for each blowpipe.
Bu adım için malzemeler:
Cam tüp3 air jets of several sizes
Mantar tıpalar1 jet corkGerekli aletler:
Bunsen beki3
3
Set up the bench
Set up the bench
Cover the bench round the blowpipe with sheet iron. Drill several holes in a block of wood so the spike can be set at different positions. Fix two taps near the bench edge, one for gas and one for air. Connect them by flexible tubes to the supplies on one side and to the blowpipe's gas inlet and air jet on the other. Ours: mild steel sheet, rubber tubing. Not given: the tap type.
Bu adım için malzemeler:
Yumuşak Çelik Sac1 bench cover
Sert Ahşap Blok1 mounting block
Bilinmeyen vana2 gas and air taps
Lastik Hortum1 flexible tubesGerekli aletler:
Sütunlu Matkap4
4
Light it and blow
Light it and blow
Light the gas at the mouth and work a foot-blower to drive air through the glass jet into the burning gas. Little air and a small jet give the pointed flame; plenty of gas and a strong blast give the large, non-luminous brush flame.
Gerekli aletler:
KörükMalzemeler
9- 1 body and side tubeYer Tutucu
- 1 brazing metal and spikeYer Tutucu
- 1 brazing fluxYer Tutucu
- 3 air jets of several sizesYer Tutucu
- 1 jet corkYer Tutucu
- 1 bench coverYer Tutucu
- 1 mounting blockYer Tutucu
- 2 gas and air tapsYer Tutucu
- 1 flexible tubesYer Tutucu
Gerekli Aletler
5- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Bağlı Plan Malzemeleri

%10 Atıf
Venetian Borax: Refining Tincal with Lime
Charlie tarafından
İnorganik
23
0
0
0
1
0

%10 Atıf
Natural Rubber Tubing, Bands and Sheet: Sulfur-Cured with Heat
Mary tarafından
Kimya
16
0
0
0
2
0

%10 Atıf
Oak Boards and Blocks, Milled and Air-Dried
Woody tarafından
Ağaç işleri
46
0
0
0
3
0

%10 Atıf
Building a Box Bellows — The Breath That Makes Metal Obey Fire
Emma tarafından
Ağaç işleri
109
0
0
0
8
0
Bu planla yapılan
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.
